Application case · Construction steel straps

Strip Punch & Cut-to-Length Line: Shaped-End Construction Straps, No Separate Punch Press

A 2-in-1 decoiler straightener and a feed-to-length strip punching and cutting machine turn 23 mm × 0.55 mm G550 high-tensile coated steel into 2,800 mm construction straps with shaped ends. There is no separate feeder or punch press in the line.

Application case · 9 min read · Factory trial run · 2 videos

Blue coated steel straps with die-cut shaped ends from a strip punch and cut-to-length line
Finished straps from the trial run. The die that cuts each strap off also shapes both of its ends.
0.55 mmG550 high-tensile coated steel strip, 23 mm wide.
2,800 mmstrap length, entered on the touchscreen.
2 machinesfrom coil to strap: a decoiler straightener and a punching and cutting machine.
≈ 1 mmmax. strip thickness where this layout can stand in for a feeder and a punch press.

This strip punch and cut-to-length line was built for a building-products maker. It makes long construction steel straps with rounded, pointed ends from narrow G550 coated strip. Each strap is 2,800 mm long, and the small piece between two strap ends is punched out as scrap. Each strap had to leave the die on its own and drop into a bin, with no one pulling it out.

A coil line with a feeder and a punch press is the usual layout. For strip this thin, the feeding and the die can share one coil-fed machine, a strip punching and cutting machine, behind a decoiler straightener. The complete line was trial-run in the HENLI factory on 23 mm × 0.55 mm strip.

The short answer

For flat parts from strip up to about 1 mm thick, a feed-to-length strip punching and cutting machine, in effect an automatic steel strip cutting machine with a custom die, can do the work of a feeder and a punch press. It feeds the length, then one die stroke cuts the piece off and shapes the ends. Thicker strip, or parts that need forming, still need a press line.

01The part

The Part: 2,800 mm Construction Straps with Shaped Ends

The straps are cut from 23 mm wide, 0.55 mm G550 high-tensile coated steel. Both ends are rounded to a point.

Construction metal straps like these are long and thin, and high-tensile strip needs a clean cut: a ragged edge on a long strap is hard to handle.

This line was set up for G550 strip, but it is a custom build: for other steel grades, coatings and thicknesses, HENLI builds the line to the customer’s material and part drawing.

  • Strip: 23 mm × 0.55 mm G550 high-tensile coated steel
  • Strap length: 2,800 mm
  • Ends: rounded to a point, the same at both ends
  • Scrap: one small butterfly-shaped piece between two straps
  • Discharge: each strap leaves the die over a downward exit guide into a bin or onto a rack; no pulling from the die
Matching shaped ends of two 2800 mm steel straps
The ends of two finished 2,800 mm straps: the same shape on both.
What the line had to do

Each strap has to leave the die on its own and drop down an exit guide into a bin, instead of an operator pulling every strap out of the die by hand.

02Line layout

Line Layout: Two Machines from Coil to Strap

The strip runs from a 2-in-1 decoiler straightener, through a free loop over a gantry loop sensor, into the strip punching and cutting machine.

StationWhat it does
2-in-1 decoiler straightenerHolds the coil, pays off the strip and flattens it with straightening rolls. See the UL 2-in-1 decoiler straightener.
Gantry loop sensorSits in the free loop between the two machines. The punching and cutting machine pulls the strip. The straightener runs only while strip is drawn, and stops when the punching and cutting machine stops.
Strip punching & cutting machineFeeds the set length, then the die cuts the strap off and shapes both ends in one stroke.
Exit guide and binFinished straps drop down the exit guide into a bin or onto a receiving rack.

Because the feeding and the die share one machine, there is no separate feeder to line up with a press. The strip punching and cutting machine cuts with a motor-driven mechanism, so it needs no air supply and no hydraulic unit.

The three stations must sit in one straight line: straightener exit, loop sensor and machine entry. If the strip runs in at an angle, the feed drifts.

Strip punch and cut-to-length line: 2-in-1 decoiler straightener, gantry loop sensor and the strip punching and cutting machine
The trial line: the decoiler straightener (right), gantry loop sensor, and the strip punching and cutting machine (left).
From coil to 2.8 m straps on the trial line: setting 2800, feeding and punch-cutting, and the finished straps (0:52).
2-in-1 decoiler straightener with an orange coil reel, straightening head and open control box Strip punch and cut-to-length line seen from the exit end: punching and cutting machine, gantry loop sensor and decoiler straightener
Left: the 2-in-1 decoiler straightener, with its coil reel, straightening head and control box. Right: the line from the exit end: the strip punching and cutting machine, the gantry loop sensor and the decoiler straightener.

03The die

One Die Stroke: Cut-Off, Both End Shapes and the Butterfly Slug

In one stroke the die cuts the strap off and shapes the end of this strap and the start of the next.

The small piece between the two ends drops out of the die as scrap. On this strap it is butterfly-shaped, and it leaves both ends rounded to a point. Because one stroke makes both ends, the two ends of every strap match.

The same kind of die can make square, chamfered or rounded ends, notches, slots or punched holes. It is built to the part drawing: send the drawing and, if you can, a short sample of your strip.

Strip passing between the upper and lower die blocks inside the punching and cutting machine Butterfly-shaped scrap slugs and test straps with shaped ends beside the machine
Left: the strip between the upper and lower die blocks. Right: butterfly-shaped scrap pieces and test straps from the trial.

04Length and batch

Setting the Length and Running a Batch

1

Enter the lengthOn the touchscreen, here 2800.0 mm. The length field reads to 0.1 mm.

2

Set the batch quantityThe machine stops automatically when the count is reached. Counters show finished pieces and batches.

3

Trim the strip headPress the manual cut button once to trim off the strip head before the run.

4

Press startThe machine feeds, cuts and drops each strap down the exit guide.

Touchscreen of the strip punching and cutting machine set to a length of 2800.0 mm with a batch quantity of 500
The touchscreen set to 2800.0 mm with a batch quantity of 500. The screens switch between English and Chinese.
Strip punching and cutting machine with its touchscreen, push buttons and feed table
The strip punching and cutting machine: the feed table and entry at the back, the touchscreen and push buttons at the front.
Short pieces first, then the production length

The trial ran short test pieces first, then the 2,800 mm production length. The change-over is made on the touchscreen: enter the new length and, if needed, adjust the feed speed.

05Why no press

Why This Strap Line Needs No Separate Punch Press

Four things about this part put it inside what one punching and cutting machine can do.

Case checkThis strap line
Strip0.55 mm G550 high-tensile coated steel, inside the range of about 1 mm
PartA flat strap: no bending or forming
Die workCut-off and both end shapes in one stroke
UtilitiesThe punching and cutting machine needs no air or hydraulic supply

For flat parts like these, the coil-fed punching and cutting machine is an alternative to a feeder and punch press: it meters the length with its feed rollers and does the die work itself. Working as a steel strap cutting machine, it cuts each strap off and shapes both ends in the same stroke. If the strip is thicker than about 1 mm, or the part has to be bent or formed, choose a press line with an NC servo feeder; HENLI can recommend a suitable press maker to go with it.

For strap parts made on a press line, see the metal hanger strap punching line. Cutting wide sheet to length with a straight shear is a different line again: see press feeding systems for cut-to-length lines.

Strip punching and cutting machine on its shipping pallet, with the strip running in from the straightener
The strip punching and cutting machine on its pallet, with the strip running in. It needs no air supply and no hydraulic unit.

06Setup tips

Setup Tips from the Trial Run

Read the strip at the straightener exit

If it curls up, the rolls press too hard: back them off. If it bends down, add pressure. Start firm and loosen a little at a time.

Lock the guides

Set the entry and exit guides to the strip width and lock them, so the strip cannot wander from side to side.

Keep one straight line

Straightener exit, loop sensor and machine entry in one line. If the strip runs in at an angle, the feed drifts.

Re-tighten the feed roller

After threading, tighten the feed roller again. If it is too loose, the length will not be accurate.

The setup video goes through each step on the trial line, from threading the straightener to the automatic run.

  1. 0:00Threading the straightener
  2. 0:51Setting the straightening rolls
  3. 1:33Exit guides and a straight strip
  4. 2:06Threading the punching and cutting machine
  5. 3:20Lining up the three stations
  6. 3:33Setting the length and quantity
  7. 4:18Jog and automatic run
  8. 4:34The whole line running

Until the strip is threaded, the screen shows an emergency-stop message and the machine will not run.

Setup and trial run: threading, straightening, lining up, setting the length and the automatic run (5:34).
Straightened strip leaving the 2-in-1 decoiler straightener through the locked exit guides Entry hold-down comb and adjustable width guide plates on the strip punching and cutting machine Red feed roller with spring pressure head on the strip punching and cutting machine
Straightened strip leaving the straightener through the locked exit guides; the entry guides; the feed roller with its pressure head.

Related machines

Related HENLI Machines

The decoiler straightener used ahead of the punching and cutting machine in this line, and the feeder to choose when the strip is thicker or the part needs forming.

?FAQ

Strip Punch & Cut-to-Length Line FAQ

Why did these straps not need a punch press?

The strap is a flat part from 0.55 mm strip, and one die stroke cuts it off and shapes both ends. A feed-to-length punching and cutting machine does that on its own. Thicker strip, or parts that have to be bent or formed, still go on a feeder and punch press line.

How are both strap ends shaped in one stroke?

The die cuts out the small piece between two straps. Its outline forms the end of one strap and the start of the next, so the two ends match. The piece drops out as scrap; on these straps it is butterfly-shaped.

How is the strap length changed?

Enter the length on the touchscreen. The same machine ran short test pieces and 2,800 mm straps; the length, and the feed speed if needed, are changed on the screen.

What machine makes construction steel straps from coil?

A strip punch and cut-to-length line: a 2-in-1 decoiler straightener and a coil-fed strip punching and cutting machine, whose die cuts each strap to length and shapes both ends. For strap steel up to about 1 mm thick it needs no separate feeder or punch press, and each strap drops into a bin on its own.

What does the line need on site?

Electric power for both machines, and room for the straightener, the loop and the punching and cutting machine in one straight line, with a bin or rack at the exit. The punching and cutting machine itself needs no compressed air or hydraulic unit.

What should I send for a quote?

The part drawing, the material grade and coating, the strip width and thickness, the coil ID, OD and weight, the lengths and batch sizes, and if you can, a short sample of the strip.

Send your part

Making Flat Parts from Thin Strip?

Send the part drawing and your strip details. HENLI will confirm whether a punching and cutting machine fits the part, and build the die to your drawing.