Stretch Leveling vs Temper Pass vs Roller Leveling: Which Flatness Process Your Parts Need
Three processes make steel strip flat, and they work in different ways and in different places. Here is what stretch leveling, a temper pass and roller leveling each do, what they correct best, and when roller leveling at your own line is enough.
Flat strip matters to every press and cutting line: it feeds straight, blanks lie flat and parts fit. Three processes are used to get there. Stretch leveling pulls the metal just past its yield point; a temper pass rolls it lightly at the mill; roller leveling bends it up and down through staggered rolls.
This guide explains how each one works, where it is done, what it corrects best and where it stops, and how to tell whether roller leveling at your own coil line is enough or the material should be bought already stretch-leveled or temper-passed. A selector points to the right route for your problem.
Stretch leveling (and continuous tension leveling) lengthens every fibre past the yield point, so it removes even large length differences such as strong edge wave or center buckle; it is done at mills and service centers. A temper pass is a light cold-rolling pass at the mill that sets the surface finish, removes the yield-point elongation behind stretcher strains and improves flatness. Roller leveling bends the strip through staggered rolls with decreasing bends; it removes coil set and crossbow, reduces mild waves and fits inline before a press or cutter. For most press and cutting lines, roller leveling is enough; severe waves with a tight flatness need call for stretch- or tension-leveled material.
01Three processes
Three ways to make strip flat
| Process | How it works | Where it is done | Corrects best | Limits |
|---|---|---|---|---|
| Roller leveling | Bends the strip up and down through staggered rolls, with smaller bends toward the exit | Inline at your press or cutting line, or at a service center | Coil set, crossbow, mild edge wave and center buckle; residual stress that curls cut parts | Strong length differences and camber; does not change the surface or remove yield-point elongation |
| Stretch leveling | Grips the strip or sheet and pulls it just past its yield point | Mills and service centers, on sheets or in continuous lines | Large length differences: strong edge wave and center buckle | Large, separate equipment; not inline at a press |
| Tension leveling | Bends the strip around small rolls under high tension | Continuous mill and service-center lines | Demanding flatness on continuous strip | Large, separate equipment |
| Temper pass (skin pass) | A light cold-rolling pass after annealing | Steel mills | Surface finish; yield-point elongation behind stretcher strains; flatness | Part of steel production, not a separate flattening step for the user |
The three are not rivals so much as stages: the mill decides the starting condition of the coil, and roller leveling at your own line takes out what coiling and handling add.
02Why strip isn't flat
Why steel strip is not flat to begin with
Most shape problems come from rolling and coiling.
Coil setWinding the strip into a coil leaves a lengthwise curve, tighter toward the inner wraps.
CrossbowA curve across the width, often from coiling and from the strip's own stresses.
Edge wave and center buckleUneven reduction in rolling leaves the edges or the middle longer than the rest, so the extra length waves.
Residual stressStress locked into the strip can stay hidden until cutting releases it and the parts curl.
What roller leveling can and cannot correct is covered in detail in the roller leveling guide.
03Roller leveling
Roller leveling: flatness at your own line
Roller leveling passes the strip through staggered work rolls that bend it up and down, with the deepest bends at the entry and smaller ones toward the exit.
Part of the thickness goes past its elastic limit, which overwrites coil set and evens out part of the length differences. Because it is continuous and compact, it sits between the decoiler and the feeder or the cutter, so the strip is flattened just before it is used.
A roller straightener with few, larger rolls takes out coil set for ordinary stamping. A precision leveler with more, smaller rolls and backup support also corrects crossbow and mild waves, and helps cut parts stay flat. Thicker or stronger strip needs larger rolls and more force.
HENLI builds both: the TL coil straightener (7 rolls, 0.35–3.2 mm), precision sheet and coil levelers (0.03–6.0 mm, Ø10–Ø54 mm rolls) and the BTL heavy duty coil leveler for heavy-gauge strip. How they are sized is in the leveler sizing guide; why roll diameter matters, in the roll diameter guide.
04Stretch and tension
Stretch leveling and tension leveling
Stretch leveling lengthens every fibre of the strip past its yield point, so short and long fibres end up the same length.
That is why it removes large length differences, such as strong edge wave or center buckle, that bending alone only reduces. On cut sheets the sheet is gripped at both ends and pulled; on continuous strip, tension leveling bends the strip around small rolls under high tension so bending and stretching act together.
Both are done on large, separate lines at steel mills and service centers. For a press or cutting shop, the practical choice is to buy the material already stretch- or tension-leveled when the part needs that flatness.
HENLI does not build stretch or tension levelers.
If your parts need that flatness, specify stretch- or tension-leveled material on the purchase order, and use a roller straightener at your line only to remove the coil set that handling adds.
05Temper pass
Temper pass: what the mill does before the coil reaches you
A temper pass, also called a skin pass, is a light cold-rolling pass that the mill gives the strip, usually after annealing.
Sets the surface finish and texture of the strip.
Removes the yield-point elongation that causes stretcher strains (Lüders lines) when some low-carbon steels are formed.
Improves flatness as a side effect.
It is part of steel production: order temper-passed material from the supplier; it is not a machine for the press shop.
06When roller leveling is enough
When roller leveling at your line is enough
For most coil-fed press and cutting lines, roller leveling is enough. The exceptions are severe shape with a tight flatness need, and surface or forming problems that come from the steel itself.
Roller leveling is enoughCoil set, crossbow, mild edge wave or center buckle, and parts that curl after cutting, on strip going into a press or cutter.
Choose a precision levelerCut sheets, laser-cut blanks, thinner strip or tighter flatness: more, smaller, supported rolls.
Buy stretch- or tension-leveled materialStrong waves with a tight flatness need, where length differences are too large for bending alone.
Buy temper-passed materialStretcher strains on formed parts, or a specified surface finish.
Test the real material: the same grade from two coils can behave differently.
Judge flatness on the part, after cutting or forming, not only on the strip.
Precision leveling and residual stress are covered in the precision leveler working principle guide.
07What to send
What to send for a leveler selection
A leveler is chosen from the hardest material it has to handle and the flatness the part needs.
- Material grade and the yield and tensile strength range
- Thickness and width combinations, including the thickest and the widest
- Photos or samples of the shape problem
- The flatness needed and how it is measured
- Coil weight and diameters
- What follows: a press, a cutter or cut sheets, and the line speed
The machine types: the leveling machine guide.
How roller leveling works and what it fixes: the roller leveling guide.
HENLI equipment
Roller straighteners and levelers
Each page has the specifications, photos and a quotation checklist.
?FAQ
Flatness process questions
What is the difference between stretch leveling and roller leveling?
Stretch leveling grips the strip or sheet and pulls it just past its yield point, so every fibre is lengthened the same and length differences disappear. Roller leveling bends the strip up and down through staggered rolls with decreasing bends; it removes coil set and much of the shape variation, and it fits inline in a press or cutting line.
What is temper leveling or a temper pass?
A temper pass, also called a skin pass, is a light cold-rolling pass at the steel mill, usually after annealing. It sets the surface finish, removes the yield-point elongation that causes stretcher strains in some low-carbon steels, and improves flatness.
What is tension leveling?
Tension leveling bends the strip around small rolls while it is held under high tension, so the combination of bending and stretching takes the material past its yield point. It is a continuous mill or service-center process for demanding flatness.
When is roller leveling enough?
For coil set, crossbow and mild edge wave or center buckle on strip going into a press or cutting line, a roller straightener or a precision roller leveler is usually enough. Severe length differences with a tight flatness requirement call for stretch- or tension-leveled material.
Can a roller leveler remove stretcher strains?
Do not rely on it. Stretcher strains come from yield-point elongation in some low-carbon steels, and the usual remedy is temper-passed material from the mill. Test the material in your forming die.
Why do parts curl after laser cutting?
The sheet still carries residual stress, and cutting releases it. A precision roller leveler with many small rolls redistributes the stress so cut parts stay flatter, though it does not guarantee that all stress is gone.
Does HENLI build stretch levelers or temper mills?
No. HENLI builds roller straighteners and precision roller levelers for coil and sheet, from thin strip to heavy-gauge coil. Stretch leveling, tension leveling and temper passes are done at steel mills and service centers.
What should I send to choose a leveler?
The material grade and strength range, thickness and width combinations, photos or samples of the shape problem, the flatness you need and how it is measured, coil data, and whether the line feeds a press, a cutting machine or cut sheets.
Send Your Material and Flatness Need
Send the material range, photos or samples of the shape problem and the flatness your parts need. HENLI will tell you whether roller leveling covers it and which leveler fits.



























































