Roller oiler troubleshooting

Roller Oiler Troubleshooting: Uneven Coating, Dry Lower Roller and Dripping

Dry spots, a dry lower roller, streaks or dripping? Find the symptom, check the likely causes in order, and fix most coating problems in a few minutes without changing equipment.

Troubleshooting guide · 7 min read · 10 symptoms

Wool felt roller oiler with brass drip valves mounted in the strip path of a press line
A CT-series wool felt roller oiler in the strip path. The brass valves along the top meter oil to each section of the upper roller.
5places most coating problems come from: alignment, delivery, contact, roller condition and the lubricant.
10symptoms in the quick finder, each with its likely causes and what to do.
0.1–0.8 MPaair pressure range for a pneumatic tank. Pressure outside it is one reason the tank does not deliver.
~2 yearsintended life of the installed felt plus the included spare set.

Most coating problems on a roller stock oiler come from five places: strip alignment, oil delivery, roller contact, the condition of the rollers and the lubricant itself. Check them in that order and most dry spots, streaks and drips can be fixed in a few minutes without changing equipment.

The checks below apply to HENLI CT-series oilers with wool felt, absorbent fiber or rubber rollers, fed from a gravity reservoir or from a pneumatic, electric-pump or press-signal tank.

The short answer

Usually the strip runs outside the felt working width, one valve is closed or blocked, the rollers were not wetted before start-up, or the felt is dirty or worn. Check alignment, delivery, contact, roller condition and the lubricant, in that order.

01Symptom finder

Quick Symptom Finder

Start from what you see on the strip or the oiler. Each row lists the likely causes and what to check and do.

SymptomLikely causesWhat to check and do
One edge or one section stays dryStrip runs outside the felt working width; head not centred on the strip; the valve for that section is closed or blockedCentre the head on the strip, confirm the working width is at least the strip width, and open or clean the valve for the dry section
Lower face stays dry (gravity felt head)Not enough oil reaches the upper felt to run down to the lower roller; rollers not wetted before start-up; too little roller contactOpen the valves gradually, wet both rollers before production and check the side adjustment that sets roller contact
Dry at start-up, fine laterThe felt was dry when the line startedWet both rollers before production and check the first strip
Coating gets thinner as speed risesDelivery is too low for the feed speed, or the lubricant is too thick at the shop temperatureIncrease delivery, confirm the lubricant suits the rollers and speed, or move to an automatic tank with adjustable flow
Streaks or lines on the stripEmbedded metal debris, damaged discs or a glazed felt surfaceClean the rollers with a compatible agent and replace damaged felt discs
Too much oil, dripping or oil on the floorValves open too far; lower trough or drain blocked; recovery container full; a kinked return hose on a pneumatic systemReduce delivery, clear the drain or return hose and empty the recovery container
Fibers or marks on aluminum or copperFelt fiber transfer on a sensitive surfaceConsider oil-resistant NBR rubber rollers, and keep the felt clean
No oil flow from the gravity reservoirReservoir empty, ball valve closed, filter screen clogged, hose kinked or the oil too thick when coldRefill, open the valve, clean the filter screen and straighten the hose
Pneumatic tank does not deliverAir pressure outside the 0.1–0.8 MPa range, timer or signal mode not set, low oil level, supply hose disconnectedCheck the regulator, the timed or signal setting, the oil level and the supply hose
The press stops on a press-signal tankThe empty-tank interlock has sent a stop signalRefill the tank and restart

02Check order

Check in This Order

1

AlignmentThe strip must run inside the felt working width, with the head set to the feed height. Slotted mounting brackets let you move the head to the strip path.

2

DeliveryOn a gravity head, the brass valves set the drip along the roller. On automatic tanks, check the flow control, air pressure or pump pressure, and the timed or press-signal setting.

3

ContactThe side adjustment sets roller contact. Too little contact leaves dry areas; the lower felt also needs enough oil from the upper felt.

4

Roller conditionLook for embedded metal debris, damage and glazing. Clean or replace the affected felt discs.

5

LubricantConfirm the oil suits the roller material, the hoses and the feed speed. Highly corrosive or acidic oils are unsuitable for absorbent fiber rollers.

6

Supply systemIf the line needs more delivery at speed, automatic start and stop with the press, or oil returned to the tank, a gravity reservoir may no longer be the right supply.

Wide perforated strip running inside the felt contact area of a roller oiler
Working-width alignment: the strip stays inside the felt contact area.
Brass drip valves, spring-loaded roller support and replaceable wool felt discs on a gravity-fed oilerSlotted mounting bracket used to align a roller oiler head with the strip path
Left: each brass valve meters oil to one section of the upper felt roller; a dry section usually means its valve needs opening or cleaning. Right: the slotted bracket lets the head be aligned with the strip path and the feed height.

03Routine checks

Routine Checks That Prevent Coating Problems

Every shift

Check the oil level, look at the coating on the first strip, and check for drips under the head.

Every week

Clean debris off the roller surfaces and check the valves, hoses and return path.

When worn

Replace felt discs before they affect the coating. Each HENLI wool felt oiler ships with one extra full set of discs matched to the roller size and working width.

After a lubricant change

Run a trial strip and re-set the delivery.

04Oil supply

When to Change the Oil Supply System

A gravity reservoir suits simple lines with manual adjustment.

Move to an automatic tank when you need oiling that starts and stops with the press, more delivery at higher speed, a low-oil alarm, an empty-tank interlock or excess oil returned to the tank. The pneumatic roller stock oiler returns excess oil to the same tank and supports timed or press-signal oiling; electric-pump and press-signal tanks are described on the coil stock oiler page.

Pneumatic oil tank control panel with timer, jog oil feed, oil level alarm and signal or time selector
The pneumatic tank controller: timer, jog oil feed, oil level alarm and the signal or time selector.

HENLI stock oilers

Spare felt, roller heads and oil supplies

Each product page has the full specifications, photos and a quotation checklist.

All stock lubrication systems

?FAQ

Roller oiler questions

Why is my stock oiler not coating evenly?

Usually the strip runs outside the working width, one valve is closed or blocked, the rollers were not wetted before start-up, or the felt is dirty or worn. Check alignment, delivery, contact, roller condition and the lubricant in that order.

Why is the lower roller dry on a gravity-fed oiler?

On the standard gravity head, oil drips onto the upper felt and runs down to wet the lower felt. If too little oil reaches the upper felt, or roller contact is too light, the lower face stays dry. Open the valves gradually and check contact.

How often should felt rollers be replaced?

Replace felt when wear, damage or debris affects oil transfer. The installed felt and the included spare set are intended to support about two years of use, depending on operating hours, material, lubricant and maintenance. See the felt roller maintenance guide.

Can I oil material thicker than 6 mm?

Standard felt heads cover material up to 6 mm: Ø32 mm rollers up to 3 mm and Ø50 mm rollers up to 6 mm. For thicker material, send an inquiry with the material, width and thickness, and HENLI will confirm a solution.

Coating problems

Still Not Coating Evenly?

Send a photo of the oiler and the strip, the lubricant and the feed speed. HENLI can check the set-up, supply spare felt or suggest a different roller or oil supply.