Stamping process · Vacuum flasks

How Are Vacuum Flasks Made? From Stainless Coil to Double-Walled Bottle

A stainless vacuum flask is two thin shells with a vacuum between them. Here is every stage, from the round blank punched from coil to the sealed, finished bottle, and the line that cuts the liner blanks.

Process guide · 12 min read · 1 video · 1 calculator

Stainless steel coil on a decoiler paying strip out to a circle blanking line
Every liner starts here: a stainless coil on the decoiler of a circle blanking line.
2 shellsAn inner liner and an outer shell, with a vacuum between them.
18/8The usual stainless grade for both shells (type 304).
≈9–15%Less strip with zigzag blanking than a single row, by blank, web and strip width.
Ø800 mmLargest blank on the HENLI zigzag servo feeder.

A good vacuum flask keeps coffee hot or water cold all day with nothing but empty space. That space sits between two stainless shells that were, not long before, flat round blanks punched out of a coil.

This guide follows a flask from coil to finished bottle: how it keeps heat in, how the inner liner is drawn from a blank, how the shells are joined and the air pumped out, and the blanking line at the start of it all. A calculator works out the liner blank, the strip and the blanks per coil for your own flask.

The short answer

Stainless steel vacuum flasks are made from two shells, an inner liner and an outer shell, usually 18/8 (304) stainless steel. Each shell starts as a round blank punched from coil, often with a zigzag feeder that nests the blanks in staggered rows, or as a welded tube. The blanks are drawn into deep cups in several stages, necked and trimmed. The liner is placed inside the outer shell and the two are joined at the neck; the space between them is pumped out in a vacuum furnace and sealed, with a getter inside to keep the vacuum. The flask is then polished or coated and fitted with its lid.

01How a flask works

Two shells and nothing between them

Heat moves in three ways: through solid material, through moving air or liquid, and as radiation. A vacuum flask blocks all three.

1

Vacuum gapWith the air pumped out from between the shells, there is almost nothing to carry heat across by conduction or convection.

2

Thin neck jointThe only solid path between inside and outside is the narrow neck where the shells meet.

3

Reflective surfaceA polished or coated wall reflects radiant heat back where it came from.

4

GetterA small getter inside the gap soaks up the last traces of gas, so the vacuum lasts.

Why stainless steel

18/8 stainless (type 304) resists corrosion and is safe for food and drink.

It draws into deep, thin-walled cups without cracking.

It polishes well, inside and out.

Inside a vacuum flask, and how its liner is drawnLeft: cross-section of a vacuum flask with the outer shell, the inner liner, the vacuum gap between them, the neck joint, the getter and the sealed evacuation point. Right: the inner liner drawn from a flat round blank into a deep cup in three draws. The liner and its blank are highlighted.Neck jointinner and outer shells joinedInner linerstainless, drawn from a blankVacuum gapair pumped outGetter and sealkeep the vacuumThe liner, blank to cupOrange: the round blank punched from coilBlankFirst drawRedrawFinal drawEach draw makes the cup narrower and deeper; theneck is formed and the top trimmed at the end.Neck jointshells joinedInner linerdrawn from a blankVacuum gapair pumped outGetter, sealkeep the vacuumThe liner, blank to cupOrange: the round blank punched from coilBlankDraw 1Draw 2Draw 3
A simplified flask. The outer shell is made the same way from a larger blank or from tube; the number of draws depends on how deep the liner is.

02The stages

From coil to finished flask

A drawn stainless flask goes through these stages. Only the first is done straight from coil; it sets up everything after it.

1

BlankingRound blanks for the liner and the outer shell are punched from stainless coil.

2

DrawingEach blank is drawn into a deep cup in several draws, then necked and trimmed.

3

JoiningThe liner goes inside the outer shell and the two are welded together at the neck; the bottom carries the evacuation point.

4

Evacuating and sealingIn a vacuum furnace the gap is pumped out and sealed, with brazing filler or a laser-sealed hole; the getter is activated by the heat.

5

FinishingPolishing, powder coating or printing, a bottom cap, and the lid.

Another route

Some makers form the liner from a welded stainless tube instead of a drawn blank.

Drawing from a blank needs no seam; tube suits some shapes and sizes.

This guide follows the drawn route.

03Blanking the liner

Punching liner blanks in staggered rows

The liner of a flask is drawn from one round blank, and a factory needs many thousands of identical blanks. Punching them straight from coil is the fast way; nesting them is the cheap way.

A straight row of round blanks leaves wide corners of scrap. A zigzag servo feeder moves the strip forward and sideways between strokes, so the die punches the blanks in staggered rows that nest into each other's gaps. On the HENLI feeder this uses about 9–15% less strip than single-row feeding, depending on the blank diameter, the web and the strip width.

1

Set it on the touchscreenEnter the strip width, blank diameter and web, press Circular auto-generate, and the controller writes the zigzag cycle.

2

Match the strip widthThe saving only appears when the strip width suits the number of blanks per row; the calculator below works it out.

3

Straight from the coilStaggered blanks are punched from the full coil width, so the coil does not have to be slit into narrow strips first.

HENLI has supplied zigzag lines for vacuum flask liner blanks; the same line makes cookware circle blanks and clutch plates.

Zigzag feeder feeding strip into a C-frame press, with the staggered round-blank skeleton leaving the die
Staggered round blanks leave a honeycomb skeleton at the die.
A zigzag blanking line punching stainless circles straight from the coil.

04Protecting the surface

Keeping polished stainless free of marks

A flask is often sold on its looks. A roll mark on the blank becomes a mark on the bottle.

1

Level before the dieThe strip passes a precision leveler so the blank is flat when it enters the draw die. HENLI SSL precision levelers choose the work-roll diameter by thickness: Ø20 mm for 0.1–0.6 mm, Ø32 mm for 0.3–1.5 mm.

2

Surface-care rollsPU-coated roll options are available for polished and stainless strip.

3

Film-covered coilCoil supplied with protective film keeps it on through blanking; the film comes off later.

4

Clean, light pressureKeep rolls and guides clean and set roll pressure no higher than needed to stop slip.

PU-coated leveling rolls on a precision leveler for surface-sensitive strip
PU-coated leveling rolls for surface-sensitive strip.

05The blanking line

The blanking line in front of the press

A liner blanking line is short: the coil, a leveler, the zigzag feeder and the press, with an outfeed for the blanks and the skeleton.

1

DecoilerAn MT decoiler for lighter coils or a hydraulic decoiler for 5–20 t. On wide zigzag lines the decoiler can travel on rails to follow the feeder's sideways swing.

2

LevelerA precision leveler flattens the stainless strip before it reaches the die.

3

Zigzag servo feederTwo servo axes: feed forward and shift across. 100–1,600 mm strip (NC‑100 to NC‑1300 standard, wider built to order), blanks up to Ø800 mm, thickness series A to D from 0.2 to 6.0 mm.

4

OutfeedThe blanks drop onto a conveyor; the skeleton is rewound on a scrap recoiler or chopped. For the press, HENLI works with partner press makers such as GOANWIN.

The complete arrangement is on the zigzag blanking line page. HENLI builds the feeder in its own factory in Dongguan, with a 15-day lead time, a 2-year warranty and CE certification.

Hydraulic decoiler, straightener and zigzag servo feeder in front of a press at a customer plant
A hydraulic decoiler, straightener and zigzag servo feeder in front of a press.

06Your liner blank

Work out the blank, the strip and the output

Enter your liner. The calculator estimates the round blank from the liner's diameter and depth, nests it on the strip with the zigzag feeder's own rule, and shows the strip width to order, the saving against a single row, the blanks per coil and the feeder and leveler that suit it.

Try itLiner blank and zigzag nestingEnter the liner diameter and depth, the trim allowance and the stainless thickness, then the zigzag pattern, coil weight and press speed. See the blank size, the strip to order, the saving against a single row and the blanks per coil.
Liner blanks nested on the stripRound liner blanks in staggered rows on the stainless strip, with the same blank in a straight single row below for comparison; the blank on the current stroke is orange.Ø261 blank · 2 / 1 zigzag · 721 mm strip7,983 blanks / coilSame blank, straight single row · strip 265 mmFeed direction → Orange: the blank on this stroke.
Liner blankØ261 mmDraw ratio 4.02: expect several draws, or a welded-tube liner
Strip to order721 mm9% less strip than single row
Blanks per coil7,983One coil runs 4.4 h at 1,800 blanks / h
Feeder and levelerZigzag servo feeder NC‑800, A seriesStrip leveling: SSL precision leveler, Ø20 rolls, surface-care rolls for polished stainless
Blank by equal surface area of a cylindrical cup, Ø = √(d² + 4 × d × depth) + trim; thin wall, corner radii ignored; the die maker sets the real blank. The draw-ratio note is a rough guide. Nesting rule of the HENLI zigzag feeder touchscreen: pitch = blank + web, rows √3 × pitch apart, one blank fewer in every second row. One blank per stroke; stainless 7,930 kg/m³. Feeder: NC‑100 to NC‑1300 standard, to 1,600 mm built to order, blanks up to Ø800 mm.

07Drawing to sealing

Drawing, joining and sealing

After blanking, the work moves to drawing presses, welders and the vacuum furnace.

1

Draw in stagesA deep, narrow liner cannot be drawn in one step; each draw makes the cup narrower and deeper, sometimes with annealing in between.

2

Neck and trimThe top is necked down and trimmed to height so the liner fits the outer shell.

3

Join at the neckLiner and shell are welded together at the mouth; the gap between them is now closed.

4

Pump out and sealIn a vacuum furnace the gap is evacuated and sealed with brazing filler or by laser; the getter is activated by the heat.

5

Test and finishFlasks are checked for heat retention, then polished, coated or printed.

Which part HENLI supplies

The blanking end: decoiler, precision leveler and zigzag servo feeder, with blank conveying and skeleton winding.

Drawing presses and dies, welding, vacuum furnaces and finishing are other equipment.

For the press, HENLI can recommend a partner press maker.

HENLI equipment

The blanking line for flask liners

Each page has the specifications, photos and a quotation checklist.

?FAQ

Vacuum flask manufacturing questions

How are vacuum flasks made?

A stainless steel vacuum flask is two shells, one inside the other. Each shell starts as a round blank punched from stainless coil, or as a welded tube, and is drawn or formed into shape. The inner liner and outer shell are joined at the neck, the air between them is pumped out in a furnace, and the evacuation point is sealed, with a getter inside to hold the vacuum. The flask is then polished or coated, and a lid is fitted.

What are vacuum flasks made of?

Mostly 18/8 stainless steel (type 304) for both shells, because it resists corrosion, is safe for food and drink, and draws well. Some outer shells are aluminum, and some liners use higher grades of stainless steel.

How does a vacuum flask keep drinks hot or cold?

Heat travels by conduction, convection and radiation. The vacuum between the two shells stops conduction and convection almost entirely; only the thin neck joint conducts, and a reflective surface or coating reduces radiation.

How is the inner liner of a vacuum flask made?

From a round stainless blank drawn into a deep cup in several draws, then necked and trimmed. Another route rolls and welds a tube and forms it to shape. The blanks are punched from coil, often with a zigzag feeder that nests them in staggered rows.

Why are flask liner blanks punched with a zigzag feeder?

Round blanks waste steel at the corners when they are punched in a straight row. A zigzag servo feeder shifts the strip sideways between strokes so the blanks nest closer; on the HENLI feeder this uses about 9–15% less strip than single-row feeding, depending on the blank, the web and the strip width.

How is the stainless surface kept free of marks?

Keep the leveler and feeder rolls clean, use PU-coated or surface-care leveling rolls where the strip is polished, and set roll pressure only as high as needed. HENLI SSL precision levelers offer PU-coated roll options.

What does HENLI supply for a vacuum flask line?

The blanking end: decoiler, precision leveler and zigzag servo feeder in front of the press, with blank conveying and skeleton winding. HENLI has supplied zigzag lines for vacuum flask liner blanks. Drawing, welding, evacuation and finishing are other equipment; for the press, HENLI works with partner press makers such as GOANWIN.

What do I need to send for a quotation?

The liner or blank drawing (blank diameter, or the cup diameter and height), the stainless grade and thickness, the coil width and weight, the press speed, and how the blanks and skeleton should leave the line.

Flask liner blanking

Send Your Liner Drawing and Coil Data

Send the liner or blank drawing, the stainless grade and thickness, the coil data and the press speed. HENLI will propose the decoiler, precision leveler and zigzag servo feeder for the blanking line.