Stamping process · Clutch plates

How Are Clutch Plates Made? Steel Plate Blanking and Flattening

The steel plates in a multi-plate clutch are blanked from coil, nested in staggered rows to save strip, then flattened, hardened and finished. Here is every stage, why plates warp, and the coil line in front of the press.

Process guide · 13 min read · 1 video · 1 calculator

A blanked steel clutch plate with internal spline and lightening holes on the exit table of a precision leveler
A blanked steel clutch plate on the exit table of a precision leveler.
2 platesSteel plates and friction plates, stacked alternately in a wet multi-plate clutch.
≈9–15%Less strip with zigzag blanking than single-row feeding, by blank diameter, web and strip width.
Ø800 mmLargest blank on the HENLI zigzag servo feeder.
0.2–6.0 mmStrip thickness across the feeder's A, B, C and D series.

Motorcycles, automatic transmissions, tractors and industrial drives all use the same kind of clutch: a stack of thin steel plates and friction plates running in oil. Every one of those steel plates was punched out of a coil of strip.

This guide follows a steel clutch plate from coil to finished part: the two kinds of plate, how the rings are nested on the strip to save steel, why blanked plates warp and how they are made flat again, and the coil line that feeds the press. A calculator works out the strip width, the saving and the plates per coil for your own plate.

The short answer

Steel clutch plates are blanked from cold-rolled steel coil. The strip is unwound, leveled and fed into a press; a zigzag servo feeder shifts it sideways between strokes so the rings are punched in staggered rows, using less strip than a single row. The die cuts the outside, the inside and the lugs or teeth in one stroke. Blanking and heat treatment leave the plates slightly warped, so they are flattened, often on a precision leveler, then heat-treated where specified, ground or finished and checked for flatness. Friction plates start with the same kind of steel core; the friction lining is then glued and cured onto both faces.

01Two kinds of plate

Steel plates and friction plates

Ask how clutch plates are made and the answer depends on which plate you mean. A wet multi-plate clutch has two kinds, stacked alternately.

1

Steel platesFlat rings of cold-rolled steel, also called separator or reaction plates. Lugs on the outside edge lock them to the clutch housing.

2

Friction platesA steel core with teeth on the inside edge that lock to the hub, and a friction lining bonded to both faces, usually with oil grooves.

3

What they shareBoth start as rings blanked from steel coil. The steel plate is finished as it is; the friction plate's core gets its lining afterwards.

A car's manual clutch is different: one dry clutch disc with a hub, damper springs and riveted facings. This guide covers the multi-plate steel parts.

Why flatness matters

The plates slide against each other when the clutch is released and clamp together when it engages.

A plate that is not flat drags, wears unevenly or chatters, so flatness is checked on every batch.

That makes flatness the thread running through the whole process.

Steel plate and friction plate in a wet multi-plate clutchLeft: a steel clutch plate, a flat steel ring with lugs on the outside edge. Right: a friction plate, a steel core with teeth on the inside edge and a grooved friction lining bonded to both faces. Both steel parts are blanked from coil.Steel plateFlat steel ring, lugs on the outsideBlanked from steel coilFriction plateSteel core, teeth inside, lining bonded onCore blanked from coil, lining added afterstackedalternatelySteel plateFlat steel ring, lugs on the outsideBlanked from steel coilFriction plateSteel core, teeth inside, lining bonded onCore blanked from coil, lining added after
In a wet multi-plate clutch the two kinds of plate are stacked alternately: the steel plates turn with the housing, the friction plates with the hub. A car's dry clutch disc is a different part, with a hub, springs and riveted facings.

02The stages

From steel coil to finished clutch plate

A steel clutch plate goes through seven stages. The first five are the press line; the last two are heat treatment and finishing.

1

Coil and levelingThe steel coil is unwound and the strip leveled, so it enters the die flat.

2

Zigzag feedingThe feeder advances the strip and shifts it sideways between strokes, nesting the rings in staggered rows.

3

BlankingOne stroke cuts the outside, the inside and the lugs or teeth.

4

FlatteningBlanked plates are passed through a precision leveler to take out the warp.

5

Heat treatment and finishingPlates are hardened where the design calls for it, then ground or finished, deburred and checked for flatness.

HENLI has built this line

HENLI has supplied complete circle blanking lines for clutch steel plates: decoiler, leveler and zigzag servo feeder in front of the press.

The zigzag blanking line page lists clutch-related auto parts among its applications.

How a steel clutch plate is madeSeven stages from steel coil to finished clutch plate: unwinding, leveling, zigzag feeding, blanking, flattening, heat treatment and finishing. The HENLI coil line and flattening stages are highlighted.1Steelcoilunwound2Levelingflat strip3Zigzagfeedingstaggered rows4BlankingOD, ID, teeth5Flatteningprecision leveler6Heattreatmenthardness7Finishinggrind, deburr, checkOrange: HENLI coil line and flattening. White: the press and die, heat treatment and finishing.1 · Steel coilunwound2 · Levelingflat strip3 · Zigzag feedingstaggered rows4 · BlankingOD, ID, teeth5 · Flatteningprecision leveler6 · Heat treatmenthardness7 · Finishinggrind, deburr, check
Steel clutch plates follow these stages. Friction plates start the same way, then the friction lining is glued and cured onto the steel core.

03Blanking from coil

Nesting rings on the strip

A clutch plate is a ring, and rings waste strip: there is steel lost between every blank and at both edges.

Feeding the strip straight, one blank per pitch, leaves wide corners of scrap. A zigzag servo feeder moves the strip forward and sideways between strokes, so the die punches the rings in staggered rows and neighbouring blanks nest into each other's gaps. On the HENLI feeder this uses about 9–15% less strip than single-row feeding, depending on the blank diameter, the web and the strip width.

1

Set it on the touchscreenEnter the strip width, blank diameter and web, press Circular auto-generate, and the zigzag servo feeder writes the zigzag cycle.

2

Match the strip widthThe saving only appears when the strip width suits the number of blanks per row. The calculator below works it out.

3

Conventional or fine blankingFine blanking gives cleaner teeth and better flatness at a higher tool and press cost. Conventional blanking on a standard press is widely used for steel plates, with flatness restored afterwards.

4

The inner slugThe centre of every ring is cut out too. It is scrap unless a smaller part is designed to be blanked from it.

Zigzag feeder feeding strip into a C-frame press, with the staggered round-blank skeleton leaving the die
Staggered round blanks leave a honeycomb skeleton at the die.

04Flatness

Why blanked plates warp, and how they are flattened

A plate punched from flat strip does not always come out flat. Two things change its shape.

1

BlankingCutting the ring out releases stresses left in the strip by rolling and coiling, and the punch leaves a burr and a slight roll-over on one side.

2

Heat treatmentHardening can distort thin plates further; the process is chosen to keep distortion low, but it is rarely zero.

Flatness is protected twice. The strip is leveled before the die, so the plate starts flat. After blanking, the plates themselves can be passed through a precision leveler. HENLI SSL precision levelers choose the work-roll diameter by thickness: Ø32 mm for 0.3–1.5 mm, Ø40 mm for 0.3–2.0 mm, Ø48 mm for 0.3–3.2 mm and Ø54 mm for 0.5–6.0 mm.

If parts are still warped after leveling, the stamped part warping guide shows how to find the stage where the shape changes.

Warped clutch plates going through an SSL precision leveler (15-second clip).
SSL precision leveler with entry and exit tables for flattening blanks and strip
An SSL precision leveler with entry and exit tables for strip and blanks.

05The coil line

The coil line in front of the press

The line in front of the blanking press has three jobs: carry the coil, deliver flat strip, and place every blank exactly.

1

DecoilerHolds the coil and pays strip off as the line takes it: an MT decoiler for lighter coils, a hydraulic decoiler for 5–20 t. On wide zigzag lines the decoiler can travel on rails to follow the feeder's sideways swing.

2

LevelerFlattens the strip before it reaches the die, so the plates start flat.

3

Zigzag servo feederTwo servo axes: one feeds the strip forward, the other shifts it across the die. 100–1,600 mm strip (NC‑100 to NC‑1300 standard, wider built to order), blanks up to Ø800 mm, thickness series A to D from 0.2 to 6.0 mm.

4

Press and outfeedThe blanks drop onto a conveyor and the skeleton is rewound or chopped. For the press, HENLI works with partner press makers such as GOANWIN; press frames are compared in the gap frame vs straight-side guide.

The complete arrangement is on the zigzag blanking line page. HENLI builds the feeder in its own factory in Dongguan, with a 15-day lead time, a 2-year warranty and CE certification.

Coil on a decoiler feeding strip across the shop floor to a zigzag feeder at a C-frame press
Coil to press: a decoiler feeding strip to a zigzag feeder at a C-frame press.
HENLI zigzag servo feeder with the servo roll-feed head on a wide traverse base
A HENLI zigzag servo feeder: the feed head rides on a wide traverse base.

06Plates per coil

Work out the strip, the saving and the output

Enter your plate. The calculator uses the same nesting rule as the zigzag feeder touchscreen to give the strip width to order, the saving against a single row, plates per coil and how long one coil runs, with the feeder width and leveler roll size that suit it.

Try itClutch plate nesting and outputEnter the plate's outside and inside diameter, the web, the thickness and the zigzag pattern, then the coil weight and press speed. See the strip width, the saving against single-row feeding, plates per coil and a matching feeder and leveler.
Zigzag layout of clutch plate blanksRing blanks in staggered rows on the coil strip, with the same blank in a straight single row below for comparison; the blank on the current stroke is orange.Zigzag, 3 / 2 per row · strip 681 mm6,155 plates per coilSame blank, straight single row · strip 154 mmFeed direction → Orange: the blank on this stroke. Grey centre: the inner slug.
Strip to order681 mm12% less strip than single row
Plates per coil6,155One coil runs 1.7 h at 3,600 plates / h
Each plate114 gMaterial use 35% · inner slug 163 g
Feeder and flatteningZigzag servo feeder NC‑800, A seriesFlatten the plates: SSL precision leveler, Ø40 rolls, working width over 150 mm
Layout rule of the HENLI zigzag servo feeder touchscreen: pitch = outside Ø + web, blanks in one row √3 × pitch apart, one blank fewer in every second row, web used as edge trim. One blank per stroke; teeth, lugs and holes are not deducted; steel 7,850 kg/m³. Feeder: NC‑100 to NC‑1300 standard, wider to 1,600 mm built to order, blanks up to Ø800 mm, thickness series A–D. Leveler roll Ø follows the SSL thickness guide. Send the plate drawing and coil data for a quotation.

07After flattening

Heat treatment, finishing and inspection

Once the plates are flat, the rest of the process is about hardness, surface and proof.

1

Heat treatmentPlates are hardened where the design specifies, by a process chosen to keep distortion low.

2

Grinding and finishingFaces may be ground or given a controlled surface; edges are deburred.

3

InspectionFlatness and thickness are checked before packing.

4

Friction platesThe steel core is cleaned and coated with adhesive, the friction lining is laid on both faces and cured under heat and pressure, and the oil grooves are finished.

Which part HENLI supplies

The coil line in front of the press: decoiler, leveler and zigzag servo feeder.

Precision levelers for flattening blanked plates.

Heat treatment, grinding and friction-lining bonding are other equipment; for the press, HENLI can recommend a partner press maker.

HENLI equipment

The line for clutch plate blanking

Each page has the specifications, photos and a quotation checklist.

?FAQ

Clutch plate manufacturing questions

How are clutch plates made?

The steel plates of a wet multi-plate clutch are blanked from cold-rolled steel coil. The strip is leveled and fed into a press, often with a zigzag feeder that punches the rings in staggered rows; the die cuts the outside, the inside and the teeth or lugs. The blanked plates are flattened, heat-treated where the design calls for it, then ground or finished and checked for flatness. Friction plates start the same way, and the friction lining is then glued and cured onto the steel core.

What are clutch plates made of?

Steel plates are cold-rolled carbon steel. Friction plates have a steel core with a friction lining on both faces, usually a paper-based or sintered material, bonded with adhesive under heat and pressure.

What is the difference between a clutch plate and a clutch disc?

In motorcycles, automatic transmissions and many industrial drives, the clutch is a stack of thin steel plates and friction plates running in oil. A car's manual clutch uses one dry clutch disc with a hub, damper springs and riveted facings. This guide covers the steel plates of the multi-plate type.

Why are clutch plates blanked with a zigzag feeder?

A clutch plate is a ring, so a lot of strip is lost around every blank. A zigzag servo feeder shifts the strip sideways between strokes, so the die punches the rings in staggered rows and the blanks nest closer together. On the HENLI feeder this uses about 9–15% less strip than single-row feeding, depending on blank diameter, web and strip width.

Why do clutch plates warp, and how are they flattened?

Blanking releases stresses in the strip and leaves a burr on one side, and heat treatment can distort the plate further. The strip is leveled before blanking, and the blanked plates can be passed through a precision leveler to bring them back flat. The stamped part warping guide explains how to find where the shape changes.

Fine blanking or conventional blanking for clutch plates?

Fine blanking shears almost the full edge and gives cleaner teeth and better flatness, but the tools and presses cost more. Conventional blanking on a standard press is cheaper and is widely used for steel plates; flatness then comes from leveling the strip and flattening the plates.

What does HENLI supply for a clutch plate line?

The coil line and the flattening: decoiler, leveler and zigzag servo feeder in front of the press, and SSL precision levelers for flattening blanked plates. HENLI has supplied complete circle blanking lines for clutch steel plates. For the press, HENLI works with partner press makers such as GOANWIN and can recommend one.

What do I need to send for a quotation?

The plate drawing (outside and inside diameter, teeth or lugs), the steel grade and thickness, the coil width, weight and inner diameter, the press speed and the flatness you need after blanking.

Clutch plate line

Send Your Plate Drawing and Coil Data

Send the plate drawing, the steel grade and thickness, the coil data, the press speed and your flatness target. HENLI will propose the decoiler, leveler and zigzag servo feeder, and the precision leveler for flattening.