Stamping process · Bearing cages

How Are Bearing Cages Made? The Pressed Steel Cage Manufacturing Process

Most tapered roller bearings carry a cage pressed from thin steel strip. Here is what the cage does, how it goes from a ring blank to a pocketed cone, and the coil line that feeds the press.

Process guide · 11 min read · 1 calculator

Motorized decoiler with pressing arm feeding a straightener and servo feeder in front of a press
The coil end of a press line: decoiler, straightener and servo feeder.
1 pocketPer roller: a cage has one window for every roller it carries.
4 stepsRing blank, drawn cone, punched pockets, sized pockets.
0.35–3.2 mmStrip range of the HENLI TL straightener for cage steel.
0.2–6.0 mmStrip range of the NC servo feeder across its series.

Open a tapered roller bearing from a car wheel or a gearbox and you will find a thin, pressed steel basket holding the rollers in place. It looks simple, but it was punched, drawn and pierced from a coil of strip.

This guide explains what a cage does, the three ways cages are made, each step of the pressed-cage process, why strip flatness and feed accuracy matter, and the coil line in front of the press. A calculator estimates the ring blank, the strip and the blanks per coil for your own cage.

The short answer

Pressed steel bearing cages are stamped from cold-rolled steel strip. The coil is unwound, straightened and fed into a press, where a ring blank is punched out and drawn into a cone with a small-end flange. The pockets that hold the rollers are then punched in an indexing die, a few at a time or all at once, and their faces are sized so they guide the rollers. After cleaning and inspection, the cage is assembled with the rollers onto the cone. Large cages can be rolled from straight strip; brass cages are machined and polymer cages are molded.

01What a cage does

Keeping the rollers in their place

A bearing would still roll without a cage, but not for long. The rollers would bunch together, rub against each other and skew.

1

SpacingIt holds every roller at the same distance from its neighbours.

2

GuidingIts pocket faces keep each roller lined up as it rolls.

3

Holding togetherIn a tapered roller bearing it keeps the rollers on the cone, so the inner ring, rollers and cage go in as one assembly.

4

LubricationOpen pockets let grease or oil reach the rollers.

Where pressed cages are used

Wheel, gearbox and differential bearings in cars and trucks.

Agricultural, industrial and electric-motor bearings.

Anywhere a tapered roller bearing is made in large numbers.

Where the cage sits, and how a pressed cage is madeLeft: half section of a tapered roller bearing with the cone, the cup, a roller and the pressed steel cage around it. Right: the cage made in four steps: a ring blank punched from coil, a drawn cone, pockets punched, and the finished cage with rollers. The cage and its blank are highlighted.Tapered roller bearingHalf section. Orange: the pressed steel cageCupouter ringRollerConeinner ringCagespaces and guides the rollersA pressed cage in four stepsOrange: the blank punched from coil, then the pocketsRing blankPunched from coilDrawn coneWall and flange formedPocketsWindows punchedFinished cageSized, rollers inPockets are punched in an indexing die, a few at a time or all at once,then their faces are sized so they guide the rollers.Tapered roller bearingOrange: the pressed steel cageCupRollerConeCageA pressed cage in four steps1 · Ring blankPunched from coil2 · Drawn coneWall and flange formed3 · PocketsWindows punched4 · Finished cageSized, rollers in
A simplified pressed window-type cage. Real cages have one pocket per roller, all the way round; large cages may be rolled from straight strip instead of drawn.

02Three kinds of cage

Pressed, machined or molded

Bearing makers choose between three kinds of cage. Pressed steel is the one made from coil.

1

Pressed steelStamped from cold-rolled strip: light, strong and cheap in volume. The usual cage in tapered roller bearings.

2

MachinedCut from brass or steel tube or forgings for large, heavily loaded or high-speed bearings.

3

Molded polymerInjection-molded glass-fibre-reinforced polyamide for many small ball and roller bearings.

4

Rolled from stripVery large cages can be bent and rolled from straight strip instead of drawn from a blank.

Why pressed steel for tapered roller bearings

Light and strong for its weight.

Cheap per piece once the dies are made.

Made straight from coil at press speed.

Pressed steelMachined brass / steelMolded polymer
Made fromCoil stripTube or forgingPellets
VolumeHighLow to mediumHigh
ToolingBlanking, drawing and pocket diesMachine toolsInjection molds
Typical useTapered roller bearingsLarge or high-speed bearingsSmall ball and roller bearings

03Pressed cage, step by step

From ring blank to pocketed cone

A pressed tapered roller bearing cage takes four main operations, usually on more than one press.

1

BlankA ring blank is punched from the strip; the centre may be punched out now or after drawing.

2

DrawThe blank is drawn into a cone, forming the wall and the small-end flange.

3

Punch the pocketsAn indexing die punches the windows one group at a time as the cone turns, or a single die punches them all.

4

Size the pocketsThe pocket faces are pressed or finished so they guide the rollers accurately; the cage is then cleaned and checked.

Small cages for high volume can be made in a progressive die; larger ones go from press to press. The same coil-to-blank start makes clutch plates and vacuum flask liners.

Close-up of the straightening rolls of a TL coil straightener
Straightening rolls: the coil set comes out before the blank is punched.

04Flat strip, exact pitch

Why flatness and pitch matter

A cage is thin and has to be round, even and true. Two things at the start of the line decide whether it will be.

1

Flat stripCoil set or waviness in the strip draws unevenly: the cone comes out out-of-round or with a wavy edge. A TL straightener takes the coil set out; its capacity table gives the width it can straighten at each thickness (for example TL‑300: 300 mm up to 1.2 mm, 85 mm at 3.2 mm, steel up to 235 N/mm² yield).

2

Exact pitchEach blank must land in the same place in the die. An NC servo feeder sets the pitch on its touchscreen and holds it, and opens its rolls for the die pilots.

3

Clean surfaceScratches and dents become stress raisers on a part that flexes in service. Clean rolls help; for polished strip, precision levelers offer surface-care roll options.

4

Cold-rolled steelCage steel is cold-rolled for an even thickness and a good draw; see the hot-rolled vs cold-rolled guide.

Servo roll feed fitted to a mechanical punch press
A servo roll feed fitted to a mechanical punch press.

05The coil line

The coil line in front of the cage press

A cage blanking line is a straightforward coil line. HENLI has supplied coil feed lines for stamped bearing cages; a typical one has three machines.

1

DecoilerAn MT decoiler holds the coil: 200–800 mm wide, 200 kg to 5 t.

2

StraightenerA TL straightener with seven rolls: 150–1,600 mm and 0.35–3.2 mm by model.

3

Servo feederAn NC servo feeder: 200–1,600 mm and 0.2–6.0 mm by series. For nested blanks on wider strip, a zigzag servo feeder.

4

PressThe blanking or first drawing press; for the press, HENLI works with partner press makers such as GOANWIN. Press frames are compared in the gap frame vs straight-side guide.

Decoiler, straightener and servo feeder feeding a press on a stamping line
Decoiler, straightener and servo feeder feeding a press.
MT decoiler, TL straightener and NC servo feeder set up as a split coil line
The same three machines set up as a split line.

06Your cage blank

Work out the blank, the strip and the line

Enter your cage. The calculator estimates the ring blank from the cone and flange, lays it on the strip in a single row or nested, and shows the strip width, the blanks per coil and the straightener and feeder that cover it.

Try itCage blank and coil lineEnter the cage's large-end and small-end diameters, its height, the small-end flange and the steel thickness, then the layout, coil weight and press speed. See the ring blank, the strip, the blanks per coil and the straightener and feeder that cover them.
Cage ring blanks on the stripRing blanks for the cage laid on the coil strip, in a single row or nested in staggered rows; the blank on the current stroke is orange and the centre hole is grey.Ø133 ring blank · single row · 139 mm strip6,785 blanks / coilFeed direction → Orange: this stroke. Grey: the centre hole.
Ring blankØ133 mmCentre hole Ø68 mm · about 80 g per cage
Strip to order139 mmSingle row, 136 mm pitch
Blanks per coil6,785One coil runs 2.8 h at 2,400 blanks / h
Straightener and feederTL‑200 straightener (steel up to 235 N/mm² yield)NC‑200 servo feeder, A series
Ring blank by equal area: cone wall π × (R1 + R2) × slant height plus the small-end flange, centre hole = small end − 2 × flange, plus trim; thin wall, radii and pockets ignored; the die maker sets the real blank. One blank per stroke; steel 7,850 kg/m³. Straightener pointer follows the HENLI TL / TL‑A capacity table for steel up to 235 N/mm² yield; feeder pointers follow the NC and zigzag tables.

07After the press

Cleaning, inspection and assembly

Once the pockets are sized, the cage goes to the bearing line.

1

Clean and deburrPress lubricant and burrs are removed so nothing reaches the rolling surfaces.

2

InspectPocket width and position, roundness and the flange are checked.

3

AssembleThe rollers are placed in the pockets around the cone and the cage is pressed to hold them there; the cup is added later.

Which part HENLI supplies

The coil line in front of the press: decoiler, straightener and NC servo feeder, or a zigzag feeder for nested blanks.

Drawing and pocket dies, presses, heat treatment and assembly are other equipment.

For the press, HENLI can recommend a partner press maker.

HENLI equipment

The coil line for bearing cage stamping

Each page has the specifications, photos and a quotation checklist.

?FAQ

Bearing cage manufacturing questions

How are bearing cages made?

Pressed steel cages are stamped from cold-rolled steel strip. A round or ring blank is punched from the coil, drawn into a cone or cup, and the pockets that hold the rollers or balls are punched in an indexing die; the pocket faces are then sized so they guide the rolling elements. Large cages may be rolled and bent from straight strip, and many small cages are molded from polyamide or machined from brass instead.

What is the manufacturing process of a taper roller bearing cage?

For a pressed tapered roller bearing cage: level the strip, feed it into the press, blank a ring, draw it into a cone with a small-end flange, punch the pockets one group at a time, size the pocket faces, then clean and inspect. The rollers are fitted into the pockets when the bearing is assembled with its cone.

What are bearing cages made of?

Pressed cages are usually low-carbon cold-rolled sheet steel. Machined cages are brass or steel; molded cages are glass-fibre-reinforced polyamide or other polymers.

What does a bearing cage do?

It keeps the rollers or balls evenly spaced, stops them touching each other, guides them as they roll, and in tapered roller bearings holds the rollers on the cone so the inner assembly can be handled as one piece.

Why does the strip have to be flat and the feed accurate?

Coil set and waviness change how the blank draws, so the cone can come out uneven or crack; an inaccurate pitch moves the blank off-centre in the die. A TL straightener takes out the coil set and an NC servo feeder holds the pitch stroke after stroke.

Single row or zigzag for cage blanks?

Small ring blanks on narrow strip usually run in a single row with an NC servo feeder. Where blanks are larger or volume is high, a zigzag servo feeder nests them in staggered rows on wider strip and uses less steel; the calculator compares both.

What does HENLI supply for bearing cage stamping?

The coil line in front of the press: decoilers, straighteners and servo feeders, or a zigzag feeder for nested blanks. HENLI has supplied coil feed lines for stamped bearing cages. Drawing and pocket dies, the presses and heat treatment are other equipment; for the press, HENLI works with partner press makers such as GOANWIN.

What do I need to send for a quotation?

The cage drawing or its blank size, the steel grade and thickness, the coil width and weight, the press speed, and whether the blanks run in a single row or nested.

Bearing cage line

Send Your Cage Drawing and Coil Data

Send the cage drawing or blank size, the steel grade and thickness, the coil width and weight, and the press speed. HENLI will propose the decoiler, straightener and servo feeder for the line.