Cylinder Head Gasket Manufacturing Process: How MLS Gaskets Are Stamped
A modern head gasket is a stack of thin steel layers, each one stamped from coil. Here is what is inside an MLS gasket, every stage from coil to finished layer, why flatness and scrap handling matter, and the coil line around the press.
A head gasket seals three things at once between the cylinder head and the block: combustion pressure, coolant and oil. In most modern engines it does that with a few sheets of thin steel, each embossed with ridges that act like springs.
This guide follows one of those steel layers from coil to finished part: what the layers do, the stages of stamping, why the strip must be precision-leveled, how the wide stainless skeleton is dealt with, and the coil line around the press. A calculator works out the strip, the skeleton, the output and the chopper for your own gasket.
Cylinder head gaskets today are multi-layer steel (MLS). Each layer is stamped from thin coil, usually spring-temper stainless steel for the outer layers. The strip is unwound, precision-leveled to take out the coil set and fed into the press by a servo feeder; the die pierces the cylinder bores, bolt holes and fluid holes, embosses the sealing beads and blanks the outline. The skeleton left behind is chopped into pieces at the die outlet. The outer layers carry a thin rubber coating; the layers are then stacked with a stopper, joined and inspected.
01Inside an MLS gasket
Thin steel layers, beads and a stopper
An MLS gasket replaced the older composite gasket because thin steel layers hold their seal under high cylinder pressure and heat.
Beaded outer layersSpring-temper stainless steel, often type 301, with ridges embossed round each bore and fluid hole. The beads act as springs that keep the seal tight as the head and block move.
StopperA folded edge, a ring or a thicker layer at the bore that stops the beads from being crushed flat.
Distance or shim layerSets the total thickness the engine needs; not every design has one.
Rubber coatingA thin elastomer coating, such as FKM, on the outer faces fills the fine surface marks of the head and block.
Each layer has its own thickness, beads and hole pattern.
Each is made on its own coil line and die.
The layers only meet at assembly.
02The stages
From coil to a finished gasket layer
One gasket layer goes through seven stages. The press does two of them; the coil line around it does the rest.
Coil and levelingThin spring stainless strip is unwound and precision-leveled flat.
Servo feedingThe strip advances exactly one gasket pitch per stroke.
Pierce and embossThe die cuts the bores, bolt holes and fluid holes and embosses the beads.
Blank and cut offThe outline is cut and the finished layer leaves the die.
Scrap choppingThe skeleton is cut into short pieces at the die outlet.
Coat and assembleLayers are coated where specified, stacked with the stopper, joined and inspected.
On cylinder head gasket stamping, HENLI has supplied the precision leveling, the servo feeding and the scrap chopper.
The die, the coating and the assembly equipment come from other suppliers.
03Flatness first
Why gasket strip must be precision-leveled
Spring stainless is thin, hard and springy. It leaves the coil curved, and it keeps that curve unless it is worked out properly.
Beads embossed into curved or wavy strip come out at uneven heights, and a layer that does not lie flat will not seal evenly in the stack. So the strip is precision-leveled before the die: many small rolls bend it up and down with shrinking amplitude until the coil set is gone.
Two stages for thin stripThe DSL dual-stage precision leveler takes 0.1–0.6 mm strip, 100–400 mm wide: a short pre-leveling section takes out most of the coil set, then a long fine-leveling section refines it.
Settings you can repeatDial indicators show the adjustment of each section, so a proven setting can be recorded for each grade and thickness.
Thicker layersStopper and shim layers above 0.6 mm go on an SSL precision leveler with larger rolls, chosen by thickness.
Check the strengthSpring-temper stainless is far stronger than mild steel, so the leveler is checked against the actual grade and width.
If layers still come out warped, the stamped part warping guide shows how to find where the shape changes.

04Feeding
Feeding a long pitch accurately
A head gasket layer runs the full length of the cylinder head, so the feed pitch is long. Every stroke, the strip has to move that far and stop in exactly the right place.
Pitch on a touchscreenThe NC servo feeder sets the feed length per stroke on its touchscreen; a new gasket needs only a new number.
Pilot releaseThe rolls open as the die pilots enter, so the pilots can set the final position of the strip.
Width and thicknessNC servo feeders cover 200–1,600 mm strip; the A series takes 0.2–2.2 mm, which covers the outer and stopper layers.
Feed along or acrossThe gasket can run lengthwise (narrow strip, long pitch) or across (wide strip, short pitch). The calculator compares both.

05The skeleton
The skeleton: wide, stiff and sharp
Cutting large cylinder bores out of every layer leaves a skeleton that is mostly holes, but still a continuous ribbon of hard stainless.
Wound up, it is springy and hard to handle; left loose, it is sharp and gets in the way. The usual answer is to chop it at the die outlet. A scrap chopper takes the skeleton straight from the die and cuts it into short pieces that drop into a bin.
Size the chopper by width and thicknessHENLI scrap choppers: SKH-100 to SKH-600 for skeletons up to 590 mm wide, MQ and HQ series for thicker scrap up to 6 mm, with SKD-11 or DC53 blades.
Match the cutting rateCuts per minute = feed pitch × press speed ÷ piece length. Longer pieces mean fewer cuts.
Test-cut hard stainlessSpring-temper stainless can need a heavier build than its width suggests; a sample test cut settles it.
06Your gasket layer
Work out the strip, the skeleton and the chopper
Enter your gasket. The calculator lays one layer on the strip, shows how much of the strip ends up as skeleton, the output per hour and per coil, and the scrap chopper, cutting rate, leveler and feeder that suit it.
07After the press
Coating, assembly and inspection
The stamped layers are not yet a gasket. Three steps follow.
CoatingThe outer layers carry a thin rubber coating on both faces; some makers stamp pre-coated coil, others coat the formed layers.
Heat treatmentSome makers temper the formed layers to relieve stress and help the beads keep their shape.
Assembly and inspectionThe layers and the stopper are stacked, joined at a few points, and checked for flatness, bead height and hole position.
The coil line around the press: decoiler, precision leveler, servo feeder and scrap chopper.
Dies, coating lines and assembly equipment are other equipment.
For the press, HENLI can recommend a partner press maker such as GOANWIN.
HENLI equipment
The coil line for head gasket stamping
Each page has the specifications, photos and a quotation checklist.
?FAQ
Head gasket manufacturing questions
How are head gaskets made?
Modern head gaskets are multi-layer steel (MLS). Each layer is made separately: thin stainless strip is unwound from a coil, precision-leveled and fed into a press, where the die pierces the bores, bolt holes and fluid holes, embosses the sealing beads and blanks the outline. The outer layers carry a rubber coating. The layers are then stacked and joined, inspected and packed.
What is an MLS head gasket made of?
Several thin steel layers. The beaded outer layers are usually spring-temper stainless steel, often type 301, with a thin rubber coating such as FKM on the outer faces. Inner stopper or distance layers may be stainless or carbon steel.
What do the beads on a head gasket do?
The embossed beads around the bores and fluid holes act as springs. When the cylinder head is bolted down they flatten and press the gasket against the head and the block; the stopper keeps them from flattening completely.
Are head gasket layers stamped or laser cut?
Volume production stamps each layer from coil: the die cuts every hole, the beads and the outline in a few strokes. Small runs and performance gaskets are often laser cut and formed separately.
Why does gasket steel need precision leveling?
The strip is thin and springy and keeps its coil set. Beads embossed into curved or wavy strip come out uneven, and the layer may not lie flat in the stack. A precision leveler, such as the DSL dual-stage leveler for 0.1–0.6 mm strip, takes the coil set out before the die.
What happens to the scrap?
A head gasket layer leaves a wide, stiff stainless skeleton with large bore holes. A scrap chopper at the die outlet cuts it into short pieces that drop into a bin, so nobody has to handle long, sharp ribbons and the skeleton never jams the line.
What does HENLI supply for a head gasket line?
HENLI has supplied the precision leveling, the servo feeding and the scrap chopper for cylinder head gasket stamping. HENLI also builds decoilers. The die, the coating line and the assembly equipment come from other suppliers; for the press, HENLI works with partner press makers such as GOANWIN.
How is a head gasket different from other metal gaskets?
Flange and flat metal gaskets are usually single-layer parts blanked from strip; the precision gasket stamping guide covers them. A head gasket is a multi-layer assembly with embossed beads and stoppers, made to seal combustion pressure, coolant and oil at once.
Send Your Gasket Drawing and Strip Data
Send the gasket drawing, the steel grade and thickness of each layer, the coil width and weight, the press speed and a skeleton sample if you have one. HENLI will propose the leveler, the servo feeder and the scrap chopper.



























































