Press feeding · Feeder types

Comprehensive Guide to Different Types of Feeders in Punching Machines: Advantages and Disadvantages

Air, roller, NC servo, gear and clamping feeders, grouped by what drives them, with the strengths and limits of each. Plus how a gear feeder works, how accurate it is and when to choose it over a servo feeder.

Selection guide · 17 min read · 1 selector

Front of a GCF high-speed gear feeder with its feed rolls, guide rolls and orange gearbox cover
The feed rolls of a GCF high-speed gear feeder.
3Drive groups: compressed air, the press itself, or a servo motor.
5Feeder types compared: air, roller, NC servo, gear and clamping.
±0.02 mmRated feeding accuracy of the HENLI GCF gear feeder.
1Question that settles gear versus servo: how often the pitch changes.

When it comes to industrial punching machines, feeders play a crucial role in ensuring precision and efficiency. These devices control the sheet metal’s movement and help with consistent feeding for uninterrupted operation. This article will examine various types of feeders, including Air Feeders, Roller Feeders, NC Servo Feeders, Gear Feeders, and Clamping Feeders, highlighting their features, benefits, and limitations.

It also explains how a gear feeder works, how accurate it is and when to choose it over an NC servo feeder, with a selector that checks your strip, pitch and press speed against the standard HENLI ranges. To go straight to the machines, compare HENLI coil feeder types side by side.

The short answer

By drive, punching-machine feeders fall into three groups: air feeders, press-driven mechanical feeders (roller, gear and clamping) and NC servo feeders. Choose by how often the pitch changes, the press speed, the strip thickness and width, and the pitch length. One fixed pitch on thin strip at high speed points to a gear or gripper feeder; a pitch that changes with every die points to an NC servo feeder; a low-cost fixed pitch at low speed, to an air feeder.

01Three drive groups

Types of Mechanical Feeders: Grouping Feeders by Drive

By what drives them, feeders for punching machines fall into three groups:

  • Air-driven: the Air Feeder, powered by an external compressed air supply.
  • Press-driven (mechanical): the Roller Feeder, Gear Feeder and Clamping Feeder, which take their motion from the punching machine itself.
  • Servo-driven: the NC Servo Feeder, powered by its own servo motor.

The three types of mechanical feeders differ in how they turn press motion into feeding: the roller feeder uses an eccentric shaft, a pull rod and a one-way bearing (see how a roller feeder works), the gear feeder uses a precise divider, and the clamping feeder uses an eccentric shaft and a crank-link mechanism with an air valve and cylinder clamp. Each type is described below.

What sets the pitch

Air feeder: an adjusting screw. Roller feeder: the crank pin on the eccentric disc. Gear feeder: a pair of change gears. Clamping feeder: the stroke of the clamp. NC servo feeder: a number on the screen.

FeederDriven byPitch set byHENLI standard rangeBest for
Air feederCompressed air: a moving clamp and a fixed clamp take turnsFine-adjustment screwAF series: 50–400 mm wide, 0.1–3.0 mm thickLow-cost fixed-pitch work on low-speed presses
Roller feederThe press output shaft, through an eccentric disc, a pull rod and a one-way clutchCrank pin position on the eccentric discRFS series: 100–700 mm wide, up to 3.5 mm, pitch up to 300 mm, up to 500 SPMFixed-pitch, high-volume stamping
NC servo feederIts own servo motorFeed length entered on the touchscreen; multi-stage programsNC series: 200–1600 mm wide, 0.2–6.0 mm thickFrequent die changes, several feed lengths, wide or thick strip
Gear feederThe press, through a timing belt and a cam indexerA pair of change gearsGCF-150 to GCF-300: 0.1–1.0 mm, pitch 12–250 mm, 600–800 SPM by modelOne pitch on thin strip at high speed: motor laminations, terminals
Clamping (gripper) feederThe press, through a cam or a crank-link mechanismClamp stroke; on the HG, a handwheel with pitch displayHG series: 8–150 mm wide, 0.04–2.0 mm, pitch up to 80 mm, up to 800 SPMShort pitches, narrow or delicate strip

02Air feeder

Air Feeder: A Basic but Effective Solution

The Air Feeder operates using an external compressed air source, directing the airflow through a five-hole valve to achieve intermittent feeding. This is usually controlled by a lever located on the punching machine’s frame.

On HENLI AF feeders, compressed air drives a moving clamp and a fixed clamp that take turns gripping the strip, with no motor or servo drive. A striker on the press slide works the trigger rod, and the feed length is set with the fine-adjustment screw at the rear.

Advantages:

  • Simple Design and Low Cost: The air feeder is straightforward, easy to install, and highly affordable compared to more complex systems.
  • Basic Operation: It requires minimal setup, making it ideal for smaller operations or businesses looking for a cost-effective feeder solution.

Disadvantages:

  • Limited Speed and Efficiency: Due to the constraints of external air pressure and flow, the feeding cycle is relatively long. As a result, it cannot handle high-speed feeding, making it more suitable for low-speed punching machines.
  • Dependency on External Air Supply: Operating an air feeder means relying on an additional air supply, which increases operational costs.
  • Feeding Inaccuracies: The simultaneous clamping and pushing of the sheet metal can lead to unpredictable sliding, affecting feeding accuracy and consistency.
AF pneumatic air feeder with its moving and fixed clamps for punch press strip feeding
An AF pneumatic air feeder: the moving clamp and the fixed clamp take turns gripping the strip.

03Roller feeder

Roller Feeder: A Mechanical Approach for Controlled Feeding

A mechanical roll feeder (roller feeder) uses a crankshaft eccentric shaft to drive a pull rod, which in turn moves the roller arm. The use of a one-way bearing converts the reciprocating motion into unidirectional feeding, and a brake device prevents the roller from moving backward.

On HENLI RFS feeders the eccentric disc fits the press output shaft and the crank pin position sets the feed length; a striker on the slide opens the rollers as the die pilots enter, and the feeder needs no electricity or compressed air of its own.

Advantages:

  • Cost-Effective and Proven Technology: The roller feeder has been in use for years and offers a solid, time-tested solution for controlled feeding.
  • Stable Feeding: The one-way mechanism ensures that the roller feeder moves in one direction, providing more reliable feeding than other manual systems.

Disadvantages:

  • Limited Feeding Length Adjustments: The feeding length is adjustable only by altering the eccentricity of the crankshaft. Adjustments require the machine to be stopped, which can lead to downtime.
  • Wear and Tear Issues: The one-way bearing operates based on friction, and this friction can cause wear over time. Factors like lubrication, spring fatigue, and temperature fluctuations can also impact the accuracy of feeding.
  • Speed Depends on Feed Pitch: The roller feeder is built for fixed-pitch, high-speed work (up to 500 strokes per minute on suitable HENLI RFS models), but short feed lengths suit the highest speeds; longer pitches need the press speed, stroke angle and release timing reviewed together.

For a fixed-pitch job, the roller feeder vs servo feeder guide compares the two in detail.

High-speed mechanical roller feeder mounted on a high-speed punch press
An RFS high-speed roller feeder on a high-speed punch press, driven from the press output shaft.

04NC servo feeder

NC Servo Feeder: Precision and Efficiency Combined

The NC Servo Feeder is driven by a servo motor that powers the roller feeder. This feeder offers advanced features, including the ability to control feeding segments and adjust feeding length with high precision.

On HENLI NC feeders the servo motor turns the lower feed roll through a timing belt, and the feed length, feeding speed and multi-stage programs are entered on a 7-inch touchscreen. The press signals each feed from its cam, and the rolls open for the die pilots with an air cylinder or a striker on the press; the feeder and press synchronization guide shows how the two stay in step.

Advantages:

  • High Precision and Versatility: The NC Servo Feeder can handle sheets of any length and provide multiple feeding segments, making it a versatile option for various punching applications.
  • Easy Operation: It is user-friendly, offering a smooth and intuitive interface for operators to adjust settings without hassle.

Disadvantages:

  • High Cost: The advanced technology and servo motor system make this feeder significantly more expensive than simpler models.
  • Slower Feeding Speed: Although highly precise, the NC Servo Feeder is not designed for high-speed feeding, limiting its use in fast-paced production environments.

How much of the press cycle a servo feed takes, and how to shorten it, is in the NC servo feeder feeding time guide.

NC servo feeder at a press with its separate control cabinet
An NC servo feeder at a press, with its separate control cabinet and touchscreen.

05Gear feeder

Gear Feeder: Synchronization for High-Speed Applications

The Gear Feeder relies on the rotation of the punching machine to drive the roller feeder. This is achieved through the use of a precise divider, which converts the rotational power into intermittent motion.

How it works

On the HENLI GCF, a timing pulley on the press output shaft drives the feeder through a timing belt. The divider is a cam indexer: it turns that continuous rotation into intermittent feed strokes of the rolls. The feed takes place over a 180° window of the crank rotation, from 270° to 90°, so the die must stay fully open throughout that window.

The pitch is set by gears. For a new pitch the N2/N3 gear pair is changed while N1 and N4 stay in place, and the gear chart on the machine lists the gears for each pitch. The feeder needs no adjustment for strip thickness.

Advantages:

  • Synchronization with Punching Machine: The gear feeder is highly synchronized with the punching machine, ensuring smooth and precise feeding during high-speed operations.
  • Ideal for Precision Feeding: This type of feeder is best suited for applications where accurate and rapid feeding is required, particularly in high-speed stamping processes.

Disadvantages:

  • Limited Flexibility: Changing the feeding length is a challenge, as it requires custom gears and adjustments to the gear transmission ratio. This customization makes the gear feeder better suited for specific stamping products rather than general-purpose applications.

On the HENLI GCF high-speed gear feeder, the pitch is set with a quick-swap N2/N3 gear pair that Henli matches to the die pitch when quoting. It is rated at ±0.02 mm feeding accuracy; actual accuracy depends on the strip, die pilots, installation, and commissioning.

GCF gear feeder drive parts: exchangeable gear sets, timing belts, output shaft, cast-iron right-angle bracket and press mounting plate
GCF drive and mounting parts: change gear sets, timing belts, the output shaft drive, the cast-iron right-angle bracket and the press mounting plate.
GCF gear feeder gear position guide with the N1, N2/N3 and N4 gears and the gear change table
Gear position guide on the GCF: N1 and N4 stay in place, the N2/N3 pair is changed, and the gear change table lists the gears for each pitch.
ModelMax. strip widthThicknessMax. speedFeed pitchFeeding accuracy
GCF-150150 mm0.1–1.0 mm800 SPM12–240 mm±0.02 mm
GCF-200200 mm0.1–1.0 mm800 SPM12–240 mm±0.02 mm
GCF-250250 mm0.1–1.0 mm600 SPM15–250 mm±0.02 mm
GCF-300300 mm0.1–1.0 mm800 SPM12–240 mm±0.02 mm

GCF-400, GCF-500 and other widths are non-standard and built to order. One feeder can cover several pitches with matching gear sets; a wide spread of pitches is checked by Henli engineers before quotation.

A GCF-250 at the factory: the mounting plate and bracket, the timing pulley and belt, then the cover opened and the middle gear pair changed, with the gear chart.
Where gear feeders are used

Fixed-pitch, long-run progressive stamping of motor stator and rotor laminations, EI laminations, terminals and connectors, and lead frames, in copper, stainless steel, silicon steel and similar thin strip. Terminal lines are covered in the gear feeder for connector terminal stamping article; mounting and tuning in the gear feed mechanism guide.

06Gear or servo

Gear Feeder or NC Servo Feeder: Which One Should You Choose?

Choose by how often the pitch changes. On a gear feeder a new pitch means a gear change; a servo feeder takes the new length on its screen. If the pitch changes often, choose a servo feeder.

A gear feeder is the stronger choice when one die runs for long periods at high speed on thin strip. The press drives it, so the feed stays tied to the crank, and the rated accuracy of the GCF is ±0.02 mm. The price is flexibility: each new pitch needs its gear pair, and the gearbox runs in an oil bath that has to be kept topped up.

An NC servo feeder is the stronger choice when dies change often, when one part needs several feed lengths, or when the strip is wider or thicker than a gear feeder takes. At high press speeds, check how long the servo feed takes for your pitch before choosing it.

Roller feeder or gear feeder?

Both are driven by the press and feed one fixed pitch per stroke.

A roller feeder makes the feed with an eccentric disc, a pull rod and a one-way clutch, and the crank pin position sets the pitch: on HENLI RFS models up to 500 SPM, 700 mm wide and 3.5 mm thick.

A gear feeder makes the feed with a cam indexer, and a gear pair sets the pitch: on the GCF, thin strip at 600 to 800 SPM.

GCF gear feederNC servo feeder
DriveThe press, through a timing belt and a cam indexerIts own servo motor, through a timing belt to the feed roll
New pitchChange the N2/N3 gear pairEnter the length on the touchscreen
Feed timingFixed by the mechanism: crank 270° to 90°Started by a signal from the press cam in each cycle
Strip0.1–1.0 mm, 150–300 mm wide (standard models)0.2–6.0 mm, 200–1600 mm wide by series
Speed600–800 SPM by modelCheck the feed time for your pitch at the press speed
Feeding accuracy±0.02 mm rated±0.05 mm per 100 mm reference
Best forOne pitch for long runs: laminations, terminals, lead framesFrequent die changes, several feed lengths, wider or thicker strip

07Clamping feeder

Clamping Feeder: A High-Speed Solution for Complex Needs

The Clamping Feeder utilizes an eccentric shaft to drive a pull rod, which activates the crank-link mechanism. The synchronized air valve and cylinder clamp and feed the sheet metal during the punching process.

HENLI builds this type as the HG series high-speed gripper feeder, driven by a cam linked to the press timing. It clamps the strip instead of rolling it, which suits short pitches and plated, soft or narrow strip: 8–150 mm wide, 0.04–2.0 mm thick, pitch up to 80 mm and up to 800 SPM on the HG-60, with ±0.025 mm feeding accuracy.

Advantages:

  • Perfect for High-Speed Feeding: This feeder is designed for high-speed feeding operations, ensuring fast and consistent material movement.
  • Easily Adjustable: The system allows for easy adjustments to meet the specific needs of various production runs.

Disadvantages:

  • Complex Mechanism: The transmission chain of a clamping feeder is long, and its intricate mechanism requires precise manufacturing and maintenance.
  • Vibration Issues: The nonlinear motion in the transmission process may lead to vibrations, which can affect the machine’s overall performance and require additional air supply support.
HG series high-speed gripper feeder for short-pitch precision stamping
An HG high-speed gripper feeder: the strip is clamped and carried forward instead of being rolled.

08Choosing

Conclusion: Choosing the Right Feeder for Your Punching Machine

Selecting the right feeder depends on your machine’s requirements and the level of performance you need. If you are working with low-speed punching machines, the Air Feeder might be enough. However, for high-speed applications, look at the press-driven feeders: the Roller Feeder for fixed-pitch work, or a Clamping Feeder or Gear Feeder for their precision and fast feeding capabilities.

For those seeking a balance between precision and ease of operation, the NC Servo Feeder offers great versatility. Meanwhile, the Roller Feeder provides a reliable and cost-effective solution for standard punching machines.

Understanding each feeder’s advantages and disadvantages is crucial to making the right decision for your punching operation. Whether you prioritize cost, speed, or precision, there is a feeder designed to meet your needs effectively.

Send these with your enquiry

Strip material, width and thickness, and the coil weight.

The feed pitch, and how often it changes or how many lengths one part needs.

The press model, its speed and stroke, and whether the die has pilots that need a release.

The line ahead of the feeder: decoiler, straightener and loop. Why pilots need the rolls opened is in the pilot release guide.

Try itWhich feeder fits the job?Choose how often the pitch changes, the press speed, the strip and the pitch. The chart checks each feeder type against its standard HENLI range.
Feeder types against the jobFive feeder types, air, roller, NC servo, gear and gripper, checked against five inputs: how often the pitch changes, press speed, strip thickness, strip width and feed pitch. Each cell says fits, check or no; the best match is highlighted in orange.Pitch changeSpeedThicknessWidthPitchAir feederfitsnofitsfitscheckRoller feederfitsnofitsfitsfitsNC servo feederfitsnofitsfitsfitsGear feederfitsfitsfitsfitsfitsGripper feederfitsfitsfitsnonofits = inside the standard range · check = ask Henli · no = outside it
Best matchGear feeder
WhyThe press drives a cam indexer, and a gear pair sets the pitch: built for fixed-pitch thin strip at 600 to 800 SPM.
AlsoNo other type covers all five inputs.
ConfirmSend the die pitch so the gear pair can be matched; pitches outside 12 to 250 mm are built to order.
Ranges are the standard HENLI catalogue ranges: AF air feeders, RFS roller feeders, NC servo feeders, GCF gear feeders (GCF-150 to GCF-300) and HG gripper feeders. Final selection depends on the strip, the die and the press; non-standard sizes can be built to order.

HENLI equipment

Feeders for punching machines

Each page has the specifications, photos and a quotation checklist.

?FAQ

Feeder type questions

What are the three types of feeders?

Grouped by drive, the three types of feeders used on punching machines are air feeders driven by compressed air, mechanical feeders driven by the press (roller, gear and clamping feeders), and NC servo feeders driven by a servo motor.

What are the four types of feeders?

The four types most often compared for punch presses are the air feeder, the roller feeder, the NC servo feeder and the gripper feeder; our air vs roller vs NC servo vs gripper feeder comparison sets them side by side. This guide also covers gear and clamping feeders.

Gear feeder or NC servo feeder: which one should I choose?

Choose by how often the pitch changes. On a gear feeder a new pitch means a gear change, so it suits one pitch run for long periods at high speed on thin strip. An NC servo feeder takes a new length on its touchscreen, so it suits frequent die changes, several feed lengths, and wider or thicker strip.

How does a gear feeder work?

The press drives it. On the HENLI GCF a timing pulley on the press output shaft drives the feeder through a timing belt, and a cam indexer turns that continuous rotation into intermittent feed strokes of the rolls. A gear pair sets the pitch.

How accurate is a gear feeder?

The HENLI GCF gear feeder is rated at ±0.02 mm feeding accuracy. Actual accuracy depends on the strip, the die pilots, the installation and commissioning.

How is the feed pitch changed on a gear feeder?

By changing gears. On the GCF the N2/N3 gear pair is changed while N1 and N4 stay in place, and the gear chart on the machine lists the gears for each pitch. Henli matches the gear pair to the die pitch when quoting, and non-standard pitches can be built to order.

What is the difference between a roller feeder and a gear feeder?

Both are driven by the press and feed one fixed pitch per stroke. A roller feeder makes the feed with an eccentric disc, a pull rod and a one-way clutch, and the crank pin position sets the pitch. A gear feeder makes it with a cam indexer, and a gear pair sets the pitch.

Should I choose a mechanical roller feeder or an NC servo feeder?

Choose a mechanical roller feeder for long runs at one fixed pitch, and an NC servo feeder when the feed length changes often or several feed lengths are needed. See our mechanical feeder vs NC servo feeder comparison for the full decision.

Feeder selection

Send Your Strip and Pitch

Tell us the strip material, width and thickness, the feed pitch and how often it changes, and the press speed. We will suggest the feeder type and model.