Aerospace Shim Stamping Line

Executive Summary:

  • An aerospace shim stamping line is a coil-fed production system for thin shim, spacer and adjustment-plate style precision parts.
  • This article focuses on line configuration from coil stock to stamped parts, not final assembly approval, controlled material compliance or part qualification.
  • Coil payoff, flatness, feed pitch, pilot release, surface protection and scrap removal all influence the stability of precision shim stamping.
  • The best setup may use a motorized decoiler, straightener, NC servo feeder, horizontal decoiler, 2 in 1 line or 3 in 1 feeding line depending on the drawing and coil data.

Aerospace shim stamping line overview with coil feeding and press line setup
Coil-fed press line overview for thin shim and metal spacer stamping.

What Are Aerospace Shims and Spacers?

In this article, aerospace shims and spacers refer to thin stamped metal parts used to adjust distance, support assembly alignment, fill controlled gaps or separate mating components. The same production logic may also apply to precision instruments, electronic assemblies, communication equipment, medical equipment housings and other applications where thin stamped parts must remain flat, clean and repeatable.

Stampable shim and spacer parts may include:

Flat shim plates
Slotted shims
Round spacers
Mounting spacers
Adjustment plates
Thin stainless shims
Aluminum spacers
Titanium alloy shims

The actual feasibility depends on the part drawing, material behavior, strip thickness, burr direction, hole layout, die design and inspection standard. A supplier should not assume that every aerospace-related shim can be made by a generic blanking process.

For a metal spacer stamping line, the safer engineering question is: what strip condition must the press receive before the die can pierce, blank and form the part repeatably?

Why Is Shim and Spacer Stamping Different from General Blanking?

General blanking often focuses on cutting the part outline quickly and economically. Precision shim stamping is more sensitive because the part is usually thin, flat, hole-rich and surface-sensitive.

  • Thin strip can deform easily during uncoiling, guiding, feeding or ejection.
  • Dense hole patterns make feed pitch and pilot entry more important.
  • Small burr growth may affect stack height, mating surfaces or assembly gap.
  • Surface scratches, roller marks or edge rub may be unacceptable on visible or functional surfaces.
  • Material springback and coil set can make the part look acceptable at the die but unstable after release.
  • Scrap webs can be narrow, sharp and easy to jam inside the die.

This is why the line should not be selected only by press tonnage or die size. The first meaningful mention of the coil decoiler machine, straightener or leveler, feeder and scrap system should be matched around the actual shim geometry and material behavior.

What Is the Typical Process Flow from Coil to Precision Shim?

A typical aerospace shim and spacer precision stamping line follows this material path:

1. Coil loading
Load and support the coil before threading.
2. Decoiling
Release strip with controlled loop or tension.
3. Straightening
Reduce coil set before feed indexing.
4. Servo feeding
Index strip into the die by programmed feed pitch.
5. Piercing and blanking
Use the die to pierce, blank and possibly form the part.
6. Scrap and parts
Remove scrap and collect finished shims or spacers.

The process looks simple on paper, but each step can change part quality. If the decoiler pulls too hard, the strip may stretch, bow or lose stable loop shape. If the straightener is not suitable for the material, coil set may remain. If the feeder slips or releases late, pilot pins may fight the strip. If scrap is not removed cleanly, small skeleton pieces can interfere with the next stroke.


Low-tension coil feeding and flatness control before precision shim stamping
Low-tension coil feeding and straightening help stabilize strip condition before the press.

For very thin or narrow strip, a horizontal decoiler or flat pallet decoiler may be considered. This layout can support delicate coils in a flatter condition and reduce side pull before the feeder. It is not the default answer for every shim line, but it can be useful when the material is narrow, light and sensitive to twisting.

What Material Handling Challenges Appear Before the Press?

Shim and spacer stamping may involve stainless steel, aluminum, titanium alloy, nickel alloy, copper alloy or coated strip, depending on the part application. This article does not recommend a specific grade or controlled material standard. The material selection must come from the buyer's drawing and approved specification.

From a feeding-line perspective, the important material questions are practical:

  • Does the strip keep strong coil set after uncoiling?
  • Is there edge wave, center buckle or crossbow before leveling?
  • Is the surface polished, coated, brushed, laminated or easy to mark?
  • Does the material require low-tension payoff to avoid stretching or distortion?
  • Are the edges sharp enough to damage guides or create side-drift risk?
  • Does the strip need controlled lubrication before the die?
  • Will the scrap web remain strong enough for stable carrying through the die?

Stainless steel often needs careful roller pressure and surface protection. Aluminum may mark more easily and can be sensitive to roller pressure, guide contact and handling dents. Titanium and nickel alloy materials may require stronger attention to straightening force, die clearance and lubrication, depending on thickness and temper. Coated strip should be handled so the functional coating is not damaged during payoff, feeding or part collection.

The line should keep the strip relaxed enough for accurate feeding and controlled enough to avoid flutter, twisting or uncontrolled slack. For precision applications, loop sensing, non-contact sensor options and brake control may be part of the decoiler decision, especially when the coil diameter changes during production.

Why Does Flatness Matter for Aerospace Shims and Spacers?

Flatness is one of the most important quality variables in a shim or spacer stamping line. A shim may be small, but if it carries coil set, edge wave or twist into the die, the part can become difficult to locate, inspect, stack or assemble.

Poor incoming flatness can contribute to:

  • Hole position drift because the strip is not sitting consistently in the die.
  • Poor pilot entry when the strip arches or waves between stations.
  • Uneven stack height when finished shims do not lie flat.
  • Inconsistent assembly gap when the spacer does not seat evenly.
  • Surface marks caused by extra guide pressure used to force the strip straight.
  • Part warping after blanking because internal stress is released unevenly.

For this reason, a precision sheet and coil leveler or suitable straightener should be evaluated before the press. The goal is not to make a marketing claim about perfect flatness. The practical goal is to reduce coil set and stabilize the strip enough for the die, pilots and feeder to work repeatably.

If the material has obvious coil memory, relying on die accuracy alone is risky. A precise die cannot fully compensate for unstable strip condition before the die.

How Should the Feeder Be Chosen for Precision Shim Stamping?

The feeder controls how much strip enters the die at each stroke. For shim and spacer parts, the right feeder depends on feed pitch, press speed, die type, part geometry, material thickness and changeover frequency.

An NC Servo Feeder is often the strongest general choice for precision shim stamping. It supports programmable feed pitch, electronic setup, recipe changeover and synchronization with the press signal. An NC servo feeder for precision stamping is especially useful when the factory runs multiple shim sizes, multiple feed lengths or progressive dies that need repeatable indexing.

A high-speed roller feeder may fit short-pitch, high-speed and stable single-product applications. When the product is consistent and the mechanical setup is correctly matched to the press, roller feeding can support fast repeated indexing. It is most attractive where speed and short feed length dominate the decision.

A pneumatic feeder may still be practical for simpler projects where the part is not extremely sensitive to feed variation and the budget is limited. It should be used carefully for precision shim or spacer work because air pressure stability, clamp condition, release timing and mechanical wear can affect repeatability.


Feed pitch and pilot release setup before a stamping press for precision shim production
Feed pitch, pilot release and press timing should be planned together for precision shim and spacer stamping.

The feeder decision should also include pilot release. If the die uses pilot pins to correct final strip position, the feeder must release the strip at the correct timing so the pilot can locate the strip without fighting feed roll pressure.

When Should a 2 in 1 or 3 in 1 Feeding Line Be Used?

Shim and spacer stamping lines can use several machine layouts. The best choice depends on material condition, floor space, press type and process sensitivity.

Use a 2 in 1 decoiler straightener plus servo feeder when the strip has visible coil set and the plant wants the feeding control close to the press. This layout combines uncoiling and straightening upstream, while the separate servo feeder indexes the strip near the die. It is useful when the material needs flattening before feeding but the press-side setup still benefits from independent feeder adjustment.

Use a 3 in 1 decoiler straightener feeder when the plant needs compact floor layout, repeatable setup and integrated control of decoiling, straightening and servo feeding. For progressive die shim and spacer stamping, this can reduce the long material path between separate machines and make setup more repeatable.


Integrated decoiler straightener feeder setup for precision coil-fed stamping
Integrated coil line setup can combine coil loading, straightening and servo feeding for repeatable press feeding.

Use a horizontal decoiler with a precision feeder when the strip is ultra-thin, narrow, light or delicate enough that vertical coil payoff creates side pull, twisting or unstable loop behavior. This is common logic in terminal and fine-strip production, and it may also apply to suitable shim and spacer applications.

Use a heavy-duty feeder or straightener when the material is thicker, stronger or harder to flatten. Do not choose heavy-duty equipment only by name. Confirm maximum strip width, thickness, material strength, feed pitch, press speed and straightening requirement before quotation.

How Can Burr, Scratch and Scrap Risk Be Controlled?

Burr control does not come from one machine alone. It depends on die clearance, punch condition, material behavior, feed stability, pilot timing, lubrication and scrap path. A stamping line should not promise a burr-free result without the actual drawing, material and inspection method. A better goal is to reduce burr risk and make burr growth more predictable.

Key control points:

  • Die clearance matched to the material and part requirement.
  • Stable feed pitch so the punch enters the intended location each stroke.
  • Correct roller pressure so the strip does not slip or get crushed.
  • Pilot release so the die can finish strip location without feeder resistance.
  • Side guides adjusted to guide the strip without rubbing the edge.
  • Proper stock lubrication system when the material and die require lubrication.
  • Clear scrap exit paths so skeleton scrap, slugs and trimmed edges do not jam.

For spacer and shim parts with many holes, slug control is especially important. Small slugs can become trapped on the die surface, damage the strip, mark finished parts or interfere with the next stroke. For continuous scrap strip, a scrap chopper or scrap collection system may be added when the scrap web is suitable for cutting and safe removal.

Surface protection should be planned before trial production. Once roller marks, guide scratches or oil stains appear on a sensitive surface, the line may need changes to roller pressure, roller material, guide shape, lubrication amount, cleaning schedule and part collection method.

What Problems Are Common in Shim and Spacer Stamping Lines?

Feed pitch variation
Hole position drift
Strip side drift
Surface scratches
Burr growth
Part warping
Poor pilot entry
Scrap jam inside die
Unstable loop control

These problems are often blamed on the press or die, but the root cause may be upstream. Coil set can create unstable strip height. Decoiler tension can affect feeding. Side guides can mark the edge. Feeder pressure can deform thin strip. Poor loop control can make the strip enter the feeder under changing tension.

Troubleshooting should start at low speed. Watch whether the strip leaves the coil smoothly, enters the straightener squarely, passes through guides without edge rub, reaches the feeder under stable tension and enters the die at the correct height.

Which Line Configuration Fits Different Shim and Spacer Applications?

Line configuration Suitable material condition Suitable product type Advantages Points to confirm
Motorized decoiler + straightener + NC servo feeder General thin to medium strip with manageable coil set Flexible shim sizes, spacer plates, progressive die work Modular layout, programmable feed pitch, easy equipment matching Loop space, feed height, line center, pilot release timing
Horizontal decoiler + precision feeder Very thin, narrow, light or delicate strip Small shims, fine spacers, surface-sensitive strip parts Lower side-pull risk, gentler coil payoff, useful for delicate coils Coil weight, strip stability, loop control, available floor space
2 in 1 decoiler straightener + servo feeder Strip with visible coil set where feeder should stay close to press Precision shims needing flatter entry before indexing Combines coil support and straightening while keeping servo feeder separate Straightening capacity, loop geometry, feeder synchronization
3 in 1 decoiler straightener feeder Compact plant layout, repeat jobs, progressive die stamping Multi-station shim and spacer stamping with repeat setup needs Integrated uncoiling, straightening and servo feeding in one system Material range, straightening force, press access, coil loading method

No configuration is automatically best for every aerospace shim and spacer project. The correct line should be selected from the part drawing, strip condition, coil data, press model, die design, required speed and surface requirement.

What Data Is Needed Before Quoting a Shim Stamping Line?

A reliable quotation should start with engineering data, not only a part name. Before specifying a precision shim or spacer stamping line, prepare:

Material type
Strip thickness
Strip width
Coil weight
Coil ID / OD
Part drawing
Hole layout
Feed pitch
Required speed
Press model
Die type
Surface requirement
Burr requirement
Floor layout
Lubrication or scrap collection

If the customer only says "we need an aerospace shim stamping line," the supplier can suggest a general direction, but cannot responsibly confirm the final line configuration. The part drawing and coil data decide whether the line should use a servo feeder, high-speed roller feeder, horizontal decoiler, precision leveler, 2 in 1 system or 3 in 1 system.

Final Notes for Line Selection

Stable production of aerospace-style shims and metal spacers is not achieved by the press or die alone. Coil release, strip flatness, feed pitch, pilot release, roller pressure, surface protection, lubrication and scrap removal all affect the finished part.

For projects involving thin metal shim production, the safest selection path is to review the material, coil data and part drawing first. Then choose the decoiler, leveler or straightener, feeder, press timing and scrap handling method as one complete line.

Send the material information, coil dimensions and part drawing when requesting line configuration advice. With those details, a supplier can compare servo feeding, roller feeding, 2 in 1 feeding and 3 in 1 feeding options more accurately.

FAQ

What equipment is used for aerospace shim stamping?

A typical aerospace shim stamping line may include a decoiler, straightener or precision leveler, NC servo feeder or high-speed feeder, stamping press, die, lubrication device, scrap removal system and part collection setup. The exact equipment depends on the material, part drawing, feed pitch, flatness requirement and surface requirement.

Why do thin metal shims need precise coil feeding?

Thin metal shims can deform, slip, wave or drift if the strip is pulled under unstable tension. Precise coil feeding helps keep the feed pitch repeatable, supports pilot entry, reduces hole position drift and helps the die work with a stable strip condition.

Should I use a servo feeder or roller feeder for spacer stamping?

Use a servo feeder when the line needs programmable feed pitch, frequent changeover or flexible spacer sizes. Use a high-speed roller feeder when the product is stable, the feed pitch is short and the press speed requirement is high. The final choice should also consider pilot release, material thickness, strip width and die timing.

How can a stamping line reduce burrs on precision shims?

A stamping line can reduce burr risk by keeping feed pitch stable, using correct pilot release, controlling roller pressure, matching die clearance, applying suitable lubrication and keeping scrap away from the die area. Burr control still depends heavily on punch condition, material behavior and the inspection requirement on the part drawing.

What data is needed before quoting a shim stamping line?

Provide material type, thickness, strip width, coil weight, coil ID and OD, part drawing, hole layout, feed pitch, required speed, press model, die type, surface requirement, burr requirement, floor layout and whether lubrication or scrap collection is needed.