Configurable motor core press feeding line

High Speed Motor Lamination Stamping Line

A coil-to-press production line for silicon steel stator, rotor, EI/UI and electromagnetic core laminations. The correct line can use double-servo feeding, high-speed single-servo feeding, gear feeding or gripper feeding depending on strip width, pitch, press speed, material surface and output-side control.

800 SPMGear feeding, fixed short pitch
60 m/minDouble servo feed and pull
35 / 45 / 60m/min laser tracking delivered
Own factoryDongguan, China
Pre-shipment motor lamination stamping line with decoiler leveler feeder press-side equipment and scrap handling
Line purposeCoil-to-press automation for motor and electromagnetic lamination stamping.
Core materialSilicon steel and electrical steel strip for stator, rotor, EI/UI and related laminations.
Main stationsCoil payoff → loop tracking → S/U leveling → selected feeding → stamping → optional pulling → scrap chopping.
Selection basisMaterial thickness, strip width, feed pitch, press speed, surface requirement and coil data.

01Definition

What Is a Stator and Rotor Lamination Stamping Line?

A lamination stamping line is an automated coil-to-press production line that stamps stator, rotor, EI/UI and other electromagnetic core laminations from silicon steel, also called electrical steel, typically 0.2 to 0.5 mm thick.

Slit coil leaves the uncoiler, often a double head decoiler, passes through a loop and a high-speed straightener, and is fed at a set pitch into a progressive die. Station by station, the die pierces the slots and then blanks the rotor and the stator. The scrap skeleton is pulled clear and chopped.

HENLI builds the coil side of this line in its own factory in Dongguan, China: uncoiler, straightener, press feeder, pulling feeder and scrap chopper. The press comes from our partner press maker, and the die from your die maker.

02Line map

Full Line Map

Start with the complete coil-to-press route before comparing individual machines. The line begins with coil payoff, stabilizes the strip through loop tracking and leveling, then moves into feeding, stamping, optional outlet pulling and scrap chopping.

Complete high speed motor lamination stamping line with double head decoiler laser tracking S type leveler feeder press pulling feeder and scrap chopper

01Coil payoff
02Laser tracking
03S/U leveler
04Feed route
05Press die
06Pull out
07Scrap chop
01 Passive or powered double-head decoiler supports coil supply and changeover.
02 Photoelectric, laser or ultrasonic loop control runs the powered decoiler.
03 S-type or U-type high-speed leveler controls strip condition before feeding.
04 GCH, GCD, gear feeder or gripper feeder is selected by pitch and strip behavior.
05 High-speed press and die stamp stator, rotor, EI/UI or electromagnetic sheets.
06 Pulling-side servo feeder can stabilize the outlet strip or skeleton after the die.
07 Scrap chopper cuts continuous skeleton waste for easier discharge and collection.
Optional automationAdvanced coil-change option

Head/tail shearing and welding can be added when coil-change downtime, material loss and long-run continuity justify the extra automation.

Where it sitsNear payoff and loop-control, before stable leveling and feeding.
Why add itTo prepare coil head/tail and reduce manual changeover interruption.
Before quotingConfirm coil change frequency, strip thickness and continuity target.

03The line

The Line Runs Left to Right

Material moves from coil payoff and strip-loop control into leveling, feeder selection, high-speed stamping and output handling. The feeder route is chosen after the strip behavior, pitch and press requirements are clear.

Motor lamination stamping line, side viewDouble head decoiler, laser loop sensor over the strip loop, S-type straightener, servo feeder, high-speed press and die, pull feeder and scrap chopper.1234567

1Double head decoiler2Loop sensor (photoelectric, laser or ultrasonic)3S-type or U-type straightener4Feeder: GCF, GCD, GCH or HG5High-speed press and progressive die6Pull feeder (optional)7Scrap chopper
Orange: coil-line machines HENLI builds in its own factory. Black: the press, through our partner press maker GOANWIN, and the die from your die maker. Schematic, not to scale.
01

Coil payoffPassive or powered decoiler

02

Loop trackingLaser / sensor control

03

Leveling routeS-type or U-type

04

Feed routeGCH / GCD / gear / gripper

05

StampingPress and die

06

Outlet controlPulling-side feeder

07

Scrap dischargeScrap chopper

04Line type

Line Type Selection by Stamped Product

Match the stamped lamination product to a practical payoff, leveling and feeder route before comparing single machines. The right route depends on strip width, thickness, pitch, press speed, surface condition and outlet control.

Equipment route
More suitable when
Typical stamped products
Typical line configuration
High-speed gear feeder line
Ultra-high speed, short pitch, mechanical synchronization and stable repeat production. It fits products where the pitch is fixed and frequent parameter changes are not the main priority.
EI/UI laminations, small rotor pieces, micro motor laminations and compact electromagnetic sheets.
Unpowered or passive decoiler → S-type or U-type leveler → high-speed gear feeder → high-speed press.
High-speed single-servo feeder line
High-speed stamping still needs flexible changeover. The strip can be pulled steadily, but the buyer runs multiple sizes or needs faster parameter setup than a gear feeder route.
Small and medium motor stator/rotor laminations, fan motor cores, BLDC motor cores, pump motor cores and appliance motor laminations.
Passive or standard payoff → S-type or suitable leveler → GCD high-speed single-servo feeder → high-speed press.
High-speed gripper feeder line
Narrow strip, thin strip, short pitch, very high press speed and surface-sensitive material where roller pressure may cause slipping, scratches or press marks.
Small motor laminations, narrow BLDC motor cores, precision electromagnetic parts and coated strip.
Compact payoff → precision leveling → high-speed gripper feeder → high-speed press.
Double-servo one-feed-one-pull line
Wide strip, longer pitch, thin silicon steel, high-value motor cores and front/rear strip condition both need control. The outlet side may affect die rhythm or scrap discharge.
EV/NEV motor stator and rotor laminations, compressor motor cores, larger servo/industrial motor cores and wide electrical steel laminations.
Powered double-head decoiler → loop tracking → S-type leveler → GCH feed-in → high-speed press → GCH pull-out → scrap chopper.
Route note: these are different strip-control approaches, not simply cheap versus expensive versions. If the strip can be pulled steadily, passive payoff with gear or single-servo feeding may be enough. If thin silicon steel, wide strip, long pitch, high coil weight or outlet-side instability makes the material hard to control, powered payoff, loop tracking and one-feed-one-pull servo control become the safer route.

05Configurations

Typical Production Line Configurations

Compare common routes for motor and electromagnetic lamination stamping. Each configuration shows the payoff, leveling, feeder, press and output-control combination normally considered for that application.

Controlled double servo motor lamination stamping line with powered payoff laser tracking S type leveler puller and scrap chopper
Configuration 01 / controlled double-servo motor core line

Powered double-head decoiler + loop tracking + S-type leveler + GCH feed and pull

EV drive motor statorEV rotor laminationCompressor motor coreLarge stator/rotor

This is the controlled route for thin silicon steel, wider strip, long or medium-long pitch and high-value motor core production. The key is not only faster feeding; the whole strip path is synchronized from active payoff to feed-in, stamping, pull-out and scrap discharge.

Stamped productsDrive motor stator sheets, rotor sheets, compressor motor stator/rotor laminations and wide motor core stacks.
Why this configurationHeavy coils, thin/wide strip and high-speed press rhythm cannot rely only on rear-side pulling.
Core control pointPayoff loop, leveling buffer, feed-in timing, die release and outlet pulling are controlled together.
Line flow: powered double-head decoiler → laser / ultrasonic / photoelectric loop tracking → S-type high-speed leveler → GCH double servo feeder → high-speed press → GCH pulling feeder → scrap chopper.
High speed single servo feeder production line for flexible motor lamination stamping
Configuration 02 / flexible high-speed single-servo line

Passive or standard payoff + leveler + GCD high-speed single-servo feeder

Fan motor coreBLDC motor coreAppliance motor laminationsSmall/medium stator rotor

This line is used when the downstream feeder can pull the strip steadily and the material does not need advanced active tension control. It is practical for medium/thin strip, multiple motor core sizes and factories that need faster changeover than a mechanical gear feeder route.

Stamped productsFan motor stators and rotors, EC/BLDC motor cores, pump motor cores and small or medium appliance motor laminations.
Why this configurationThe material can be pulled smoothly, while servo parameter setup helps with product changeover.
Core control pointLeveling quality, feed length, press signal, pilot release and changeover flexibility.
Line flow: passive or standard decoiler → S-type or suitable leveler → GCD high-speed single-servo feeder → high-speed press.
High speed gear feeder production line for short pitch lamination stamping
Configuration 03 / short-pitch gear feeder line

Unpowered decoiler + S/U leveler + high-speed gear feeder

EI laminationUI laminationSmall rotor blankMicro motor core

The gear feeder route is for short-pitch, high-SPM, fixed or stable products. It is not chosen because it is a lower version; it is chosen because mechanical synchronization can be very suitable when the product is fixed and the feeding pitch is short.

Stamped productsEI/UI laminations, small rotor pieces, micro motor laminations, compact magnetic sheets and other stable short-pitch blanks.
Why this configurationShort pitch and fixed production benefit from mechanical timing and repeated stable indexing.
Core control pointPress shaft synchronization, feed pitch, material thickness, die timing and product change frequency.
Line flow: unpowered decoiler → S-type or U-type leveler → high-speed gear feeder → high-speed press and die.
High speed gripper feeder production line for narrow strip short pitch lamination stamping
Configuration 04 / narrow-strip gripper feeder line

Compact payoff + precision leveling + high-speed gripper feeder

Narrow BLDC coreMicro motor laminationThin electromagnetic stripSurface-sensitive material

The gripper feeder line is a specialized route for ultra-high-speed, short-pitch, narrow and thin strip. It is especially useful when roller feeding may slip, scratch, press marks into the material or become unstable at very high press speed.

Stamped productsSmall motor laminations, narrow BLDC cores, precision electromagnetic parts and coated or plated strip with surface requirements.
Why this configurationClamp-move-release feeding reduces rolling friction and helps protect thin or coated strip surfaces.
Core control pointStrip width, pitch, clamping pressure, surface coating, press speed and die release timing.
Line flow: compact decoiler → precision leveling → high-speed gripper feeder → high-speed press.
U type high speed leveler production line for EI UI electromagnetic lamination stamping
Configuration 05 / EI/UI and reactor sheet line

Decoiler + U-type high-speed leveler + gear or selected short-pitch feeder

Transformer EI sheetsUI laminationsReactor sheetsInductor core sheets

EI/UI, transformer and reactor laminations usually require strong flatness control and stable short-pitch feeding. A U-type high-speed leveler with a gear, gripper or selected short-pitch feeder can be considered when stacking quality and sheet geometry are the main concerns.

Stamped productsTransformer EI laminations, UI laminations, reactor core sheets, inductor core sheets and flatness-sensitive silicon steel blanks.
Why this configurationWhen flatness affects stacking and magnetic-core quality, leveling priority can be higher than long-pitch servo control.
Core control pointFlatness, sheet geometry, short pitch, press/cutting rhythm and whether gear or gripper feeding fits the material.
Line flow: passive or powered decoiler → U-type high-speed leveler → gear feeder / gripper feeder / suitable short-pitch feeder → high-speed press or cutting station.

06Stations

Station-by-Station Line Walkthrough

Each station below explains what happens in the production line, why it matters and which Henli machine can be used there.

01Coil payoff

Choose passive or powered payoff by strip tension and coil-change needs

The decoiler is the first station, but it does not have one fixed specification. A passive double-head decoiler can work when the downstream leveler and feeder can pull the strip smoothly. A powered double-head decoiler is used when coil weight, strip sensitivity, line speed or loop stability requires active payoff control.

Unpowered double head decoiler for passive coil payoff in high speed lamination line

Passive double-head decoiler

Supports the coil, controls braking and lets the downstream equipment pull the strip. Use it when material rigidity, coil weight and strip tension are manageable.

Best with: leveler → gear feeder or GCD single-servo feeder → high-speed press.
Powered double head decoiler for active coil payoff in motor lamination line

Powered double-head decoiler

Actively pays off material so the strip loop stays controlled. Use it for heavier coils, thin or wide silicon steel and lines where rear-side pulling alone is not stable enough.

Best with: loop tracking → S-type leveler → GCH feed-in and optional pull-out.

View Double Head Decoiler

02Loop tracking

Loop control keeps the powered decoiler in step with the strip loop

Station 02 is the loop detection area. A standard powered double head decoiler uses a photoelectric sensor and works start-stop at 20 m/min. Laser loop tracking is the option for faster lines: it reads the loop height continuously and changes speed steplessly, and we have delivered it on 35, 45 and 60 m/min lines. Ultrasonic sensing is also stepless. The laser sensor does not touch the strip, which suits surface-sensitive material. The purpose is payoff synchronization, not strip cutting or welding.

Decoiler speed over timeA standard powered decoiler with a photoelectric sensor switches between 20 m/min and stop; a laser loop tracking decoiler changes speed smoothly.200Timem/minPhotoelectric (standard): start-stop at 20 m/minLaser or ultrasonic (option): stepless
Laser loop tracking has been delivered on 35, 45 and 60 m/min lines. Illustration of the control behavior, not measured data.
Laser tracking powered double head decoiler line overview for high speed motor lamination stamping

Loop height is the control signal

Photoelectric sensing starts and stops a standard powered decoiler. Laser or ultrasonic sensing changes its speed steplessly, so the loop does not shake, pile up or pull tight.

Laser tracking powered double head decoiler workshop view

Active payoff supports sensitive strip

This route is especially useful for thin silicon steel, wider strip and high-speed motor lamination lines where unstable tension can scratch material or disturb feeding rhythm.

Advanced option: strip head/tail shearing and welding

This coil-change module is added when the buyer wants to reduce coil-change downtime, connect coil head and tail more efficiently, and keep long-run lamination stamping more continuous. Also called a coil end welder or strip end joiner; HENLI builds it in its own factory.

  • Use it when coil change frequency, material loss and downtime are important.
  • It belongs around the coil-change area, before the strip enters stable leveling and feeding.
  • Confirm whether the project really needs this automation before adding it to the proposal.
Strip head tail shearing and welding unit as optional coil joining module for lamination stamping line
Optional module for coil head/tail preparation and joining in high-end continuous lines.
03Leveling route

S-Type or U-Type Straightener: choose by material, cycle and floor space

The leveler, also called a coil straightener, is the bridge between coil payoff and press feeding. Both types straighten the strip and hold a reserve ahead of the feeder; the S-type is also called an S-loop straightener. The final choice depends on material, feeding cycle and floor space, and neither needs a loop pit.

S-type and U-type straightener loopsThe S-type holds the strip reserve in an S-shaped loop inside the machine; the U-type lets the strip hang in a U loop watched by two photoelectric sensors, one to slow down and one to stop.S-type: S-shaped loop inside the framestopslowU-type: U loop on a flat floor, two sensors
Neither type needs a loop pit. The U-type has more rollers and is usually chosen for EI/UI and reactor sheets; the S-type for stator and rotor lines with a longer pitch. Schematic.
S type high speed leveler for motor lamination stamping line

S-type high-speed leveler

Usually used on stator and rotor lines with a longer pitch: EV motor core, compressor motor core, BLDC, servo motor and larger stator/rotor lamination lines.

Best with: powered or passive decoiler → S-type leveler → GCH / GCD / selected feeder → high-speed press.
U type high speed leveler for EI UI and transformer lamination line

U-type high-speed leveler

The U-type has more rollers and is usually chosen for EI/UI laminations, transformer cores, reactor sheets and other flatness-sensitive electromagnetic sheets. It reduces coil set and crossbow and improves center buckle and edge wave.

Best with: decoiler → U-type leveler → gear feeder / gripper feeder / suitable short-pitch route.

View S-Type Leveler | View U-Type Leveler

04Feed route

Select the feeder route after material and press data are clear

The feeder is not chosen by product name alone. It is selected after the material, pitch, press speed, surface requirement and outlet behavior are clear. GCH, GCD, gear feeder and gripper feeder solve different strip-control problems in high-speed lamination stamping lines.

GCH double servo feeder installed at press side for motor lamination stamping
GCH double servo feeder route

For wide or thin silicon steel, longer pitch and one-feed-one-pull control

GCH is the main route for demanding motor lamination lines. In a controlled line, one double servo feeder sends the strip into the press, and another double servo unit can work as the pulling feeder after the die.

Use whenEV motor cores, compressor motor cores, larger stator/rotor laminations, thin silicon steel and wide strip.
ConfirmStrip width, thickness, feed pitch, press signal, pilot release and whether outlet pulling is needed.
High speed single servo feeder for flexible motor lamination press feeding
GCD high-speed single servo feeder route

For stable rear-side pulling and flexible product changeover

This route fits medium/thin strip and mixed motor lamination programs. If the material can be pulled steadily without advanced active payoff control, a single-servo line is simpler and more flexible than a mechanical fixed-pitch route.

Use whenFan motor, BLDC motor, small and medium stator/rotor laminations, multi-size production.
ConfirmMaterial range, feed length, product mix, press speed, changeover frequency and layout space.
High speed gear feeder for short pitch lamination stamping
High-speed gear feeder route

For short pitch, high SPM and fixed repeat production

Gear feeding is strong when the pitch is short, the press speed is high and the product is stable. It is suitable for EI/UI, micro motor and fixed lamination programs where mechanical synchronization is valuable.

Use whenEI/UI laminations, micro motor rotors, compact electromagnetic sheets and short-pitch fixed products.
ConfirmFeed pitch, press shaft connection, material thickness, stroke speed and whether frequent product change is required.
High speed gripper feeder for narrow strip short pitch precision stamping
High-speed gripper feeder route

For narrow, thin, short-pitch and surface-sensitive strip

The gripper feeder is not a general-purpose feeder. It is for ultra-high-speed short-pitch work where roller pressure may cause slipping, scratching or surface marks. The clamp-move-release action protects strip movement in specific precision stamping lines.

Use whenSmall motor laminations, narrow BLDC cores, precision electromagnetic parts and coated/surface-sensitive strip.
ConfirmStrip width, pitch, thickness, coating, clamping pressure, target SPM and die release timing.

View GCH Double Servo Feeder | View GCD High Speed Servo Feeder | View High-Speed Gear Feeder | View High Speed Gripper Feeder

05Press stamping

The press and die decide how the feeder must synchronize

In a real project, the feeder, leveler and decoiler must match the high-speed press signal, die release timing, feed pitch, bed width and material path.

We can recommend a suitable press maker through our partner GOANWIN. The die comes from your die maker.

  • Confirm press model, tonnage, bed width, stroke and target SPM.
  • Confirm feed pitch, pilot release, press angle signal and die layout.
  • For wide or thin strip, review whether feeding-side and pulling-side control are both needed.
High speed press die and feeder synchronization in motor lamination stamping line
The press, die, feeder guide, pilot release and press angle signal must be treated as one synchronized stamping station.
06-07Outlet side

Pulling and scrap chopping keep the press outlet under control

After stamping, the strip skeleton can be long, sharp and difficult to collect. A pulling-side feeder stabilizes the output path when the die outlet affects strip movement, and a scrap chopper cuts continuous skeleton waste into shorter pieces.

One feed, one pullA GCH double servo feeder pushes the strip into the die and a second GCH pulls the strip or skeleton out after the die, before the scrap chopper.Feed-in GCHPress and diePull-out GCH
Used for thin or wide silicon steel and longer pitch, where the outlet side affects the die rhythm. Schematic.
  • Use the rear servo feeder as a pulling unit when the die outlet side affects strip stability or press rhythm.
  • Use a scrap chopper when continuous skeleton waste needs safer, shorter discharge.
  • Match the scrap chopper by scrap width, thickness, shape, outlet height and press signal.
  • View Punch Scrap Chopper Machine
Double servo feeder used as pulling unit before high speed scrap chopper
In a one-feed-one-pull motor lamination line, the rear double servo feeder pulls the strip or skeleton after stamping before scrap cutting.
Press scrap chopper machine for motor lamination line waste handling
Scrap chopper after the press outlet.
Scrap chopper integrated with high speed press feed line
Output-side scrap handling as part of the full line.

07Cases

Real Workshop Production Line Cases

These site photos show how the line routes above appear in real factory layouts: controlled double-servo motor lamination lines, pre-shipment line integration, high-speed single-servo feeding, gripper feeder lines, gear feeder lines and finished lamination output.

Double servo motor lamination press feeding line site with high speed press
Case 01 / double-servo lineMotor lamination press feeding siteShows a controlled line route for motor core stamping where the feeder and press must work as one system.
Wide workshop view of double servo press feeding line for motor lamination stamping
Case 02 / workshop layoutWide view of the press feeding lineShows floor layout, press position, feeder placement and operator-side access.
Close up of double servo feeder installed beside high speed press
Case 03 / press sideDouble servo feeder close to the pressHighlights the press-side feeder position where feed pitch, guide, release timing and press signal are matched.
Double servo feeding line integrated with high speed press at workshop site
Case 04 / high-speed pressDouble-servo line with high-speed pressSupports one-feed-one-pull control for demanding motor lamination stamping projects.
Factory installation of double servo motor lamination stamping line
Case 05 / installationFactory installation stageShows the practical installation environment before final tuning, press matching and production handover.
Pre shipment overview of motor lamination press feeding line
Case 06 / pre-shipmentComplete line before deliveryLine integration before delivery: decoiling, leveling, feeding and press-side matching are checked together.
Side view of motor lamination press feeding line before shipment
Case 07 / side viewSide view of the line routeHelps buyers understand line length, material path and how each machine sits before the press.
GCD 400 high speed single servo feeder line application for press feeding
Case 08 / GCD routeHigh-speed single-servo lineFits flexible motor lamination programs where the strip can be pulled steadily and fast changeover matters.
High speed gripper feeder narrow strip press line site
Case 09 / gripper routeNarrow-strip gripper feeder siteShows the specialized short-pitch route for thin, narrow or surface-sensitive strip feeding.
High speed gripper feeder coil to press line application
Case 10 / coil to pressGripper feeder coil-to-press layoutConnects compact payoff, strip preparation and high-speed press feeding for precision narrow-strip work.
High speed gear feeder short pitch press line application
Case 11 / gear routeShort-pitch gear feeder lineGear feeding provides stable mechanical synchronization for EI/UI, micro motor and other fixed short-pitch products.
Motor lamination stacks on workshop pallet after stamping production
Case 12 / stamped outputStamped lamination outputShows finished motor lamination stacks as the production result of coil-to-press line integration.
Field casesWhat these cases show

The site photos show line layout, press-side placement, feeder route and stamped output for different motor lamination projects.

Identify the routeDouble-servo, single-servo, gear or gripper feeder line.
Check the control pointsPayoff, loop tracking, leveling, press signal and outlet handling.
Match the productMaterial, pitch, line speed and stamped lamination output decide the route.

08Applications

Stamped Products and Production Lines Covered

The following motor and electromagnetic lamination applications share coil-to-press stamping requirements. Each row connects the stamped product to a likely payoff, leveling and feeder path.

Application line Stamped products Recommended production-line path Selection factors
EV / NEV motor core line Drive motor stator laminations, rotor laminations, stator core stacks and rotor core stacks. Powered double-head decoiler → loop tracking → S-type leveler → GCH feed-in → high-speed press → GCH pull-out → scrap chopper. Use this path when the strip is thin, wide, valuable or difficult to keep stable at high speed.
Compressor motor core line Air conditioner compressor motor stator/rotor, refrigerator compressor laminations and appliance compressor cores. Double-head decoiler → S-type leveler → GCH or GCD feeder → high-speed press → optional outlet control. GCH fits wider/thinner or more demanding lines; GCD can fit stable medium/thin strip with more product changeover.
BLDC / fan / pump motor core line BLDC stator and rotor laminations for fans, pumps, drones, robots, range hoods, air purifiers and compact drive motors. S-type leveler + GCD for flexible programs; gear or gripper route for narrow, short-pitch products; GCH for wider or higher-control lines. Choose by strip width, pitch, surface sensitivity and whether the buyer runs one stable product or many sizes.
Servo / stepper motor lamination line Precision stator laminations, rotor laminations and compact motor core stacks. Passive or powered payoff → S-type leveler → GCH, GCD or selected feeder → high-speed press. The line can be single-servo or double-servo depending on strip width, pitch and whether outlet pulling is needed.
Industrial large motor core line Large stator laminations, rotor laminations, wide electrical steel sheets and large motor core stacks. Higher-capacity powered payoff → S-type high-speed leveler → wide GCH feeder → wide-bed press → output-side control. Wide material and large dies push the line toward controlled payoff, wide feeding and careful press synchronization.
Micro motor lamination line Small DC motor rotor pieces, micro motor stator/rotor laminations and compact narrow-strip motor blanks. Compact decoiler → precision leveling → gear feeder or gripper feeder → small high-speed press. Short pitch and narrow strip often matter more than long-pitch servo control.
EI / UI transformer lamination line EI silicon steel laminations, UI laminations, transformer core sheets and stacked magnetic-core pieces. Passive or powered decoiler → U-type high-speed leveler → gear feeder or suitable short-pitch feeder → press or cutting station. Flatness and stable short-pitch feeding are the main selection drivers.
Reactor / inductor electromagnetic sheet line Reactor sheets, inductor core sheets, magnetic sheets and other flatness-sensitive electromagnetic blanks. Decoiler → U-type leveler → gear feeder, gripper feeder or suitable cutting/press route. Confirm the final machine path by sheet shape, strip flatness requirement, pitch and tolerance.
Coil line for an existing press Stator, rotor or EI/UI production where the press and die are already in place. Payoff, loop control, S/U straightener, GCH, GCD, gear or gripper feeder, or scrap chopper matched to the press. Chosen by strip, pitch, press speed, line height and floor space.

Related short-pitch stamping fields include filter end caps, chain plates, razor blades, battery busbars, connector terminals and heat sink fins. These need their own material, die and output-handling review; this line is configured for motor laminations, silicon steel and electromagnetic cores.

09Output

Stamped Output From These Lines

Typical stator, rotor and EI laminations stamped on these production lines.

Progressive die strip layoutGeneric strip layout: pilot holes, rotor slots, rotor blanked out, stator slots, then the stator blanked out, one station per press stroke.Pilot holes1 Rotor slots2 Rotor blanked3 Stator slots4 Stator blankedStrip advances one pitch per stroke
A generic layout. Real dies differ in rows, slot shape and stacking; the die comes from your die maker, and the coil line holds pitch, timing and strip condition.
Stacked motor stator laminations from high speed lamination stamping line
Stator stack
Motor stator and rotor lamination core stack
Stator/rotor core
Motor stator lamination sheet top view
Stator sheet
Motor rotor lamination sheet top view
Rotor sheet
EI silicon steel lamination stack
EI lamination

10Feeder

Feeder Selection Comes After the Line Type

The feeder is selected after the buyer confirms product type, strip width, material thickness, feed pitch, press speed, surface requirement and outlet-side behavior.

Equipment / feeder path More suitable when Typical stamped products Data to confirm
High-speed gear feeder
Passive decoiler + S/U leveler + gear feeder
Ultra-high speed, short pitch, mechanical synchronization and fixed or stable repeat products. EI/UI laminations, small rotor pieces, micro motor laminations and compact electromagnetic sheets. Terminals/connectors are adjacent short-pitch applications. Feed pitch, press shaft connection, material thickness, coil weight and whether product changeover is frequent.
High-speed single-servo feeder / GCD
Passive or standard payoff + leveler + GCD
High-speed stamping with flexible changeover, medium/thin strip, mixed programs and programmable feed length. Small and medium motor stator/rotor programs, fan motor cores, BLDC motor cores and pump motor cores. Part mix, strip width, feeding length, target SPM, material surface, press signal and layout space.
High-speed gripper feeder
Compact payoff + precision leveler + gripper feeder
Narrow strip, thin material, very short pitch, very high press speed and surface-sensitive material where roller marks or slip must be avoided. Small motor laminations, narrow BLDC strip, micro motor laminations, precision electromagnetic parts and coated strip. Strip width, pitch, thickness, surface coating, clamping pressure, press speed and tool release timing.
Double-servo one-feed-one-pull / GCH
Powered double-head decoiler + loop tracking + GCH feed and pull
Wide strip, longer pitch, thin silicon steel, high-value motor cores, press synchronization and front/rear strip control. EV motor core, compressor motor core, larger servo/industrial motor cores, wide stator/rotor and high-value silicon steel lines. Coil weight, strip width, thickness, feed pitch, press angle signal, die release timing, pulling requirement and scrap discharge.

11Specifications

Strip, Pitch and Speed Range by Machine

The listed limits of each HENLI model in the line. Maximum pitch and maximum SPM are not reached at the same time; what a line runs depends on strip, pitch, die and press.

Station Model Thickness Width Pitch / load Speed Feed accuracy
Gear feeder GCF-150 / 200 / 300 0.1–1.0 mm 150–300 mm 12–240 mm 800 SPM ±0.02 mm
Gear feeder GCF-250 0.1–1.0 mm 250 mm 15–250 mm 600 SPM ±0.02 mm
Gripper feeder HG-60 / 80 / 80W 0.04–2.0 mm 8–110 / 8–110 / 8–150 mm 0–60 / 0–80 / 0–80 mm 800 / 700 / 400 SPM ±0.025 mm
Single servo feeder GCD By model By model Programmable For high-speed presses ±0.02 mm
Double servo feeder GCH 0.2–2.0 mm By model Programmable 60 m/min —
S-type straightener TUS-200 / 300 / 400 0.1–1.0 mm 200 / 300 / 400 mm — 60 m/min —
U-type straightener JMU-200 / 300 / 400 0.1–1.0 mm 200 / 300 / 400 mm — 0–60 m/min —
Double head decoiler MTD-200 / 300 / 400 — 200–400 mm 500 / 800 / 1,200 kg per side 20–60 m/min —

Wider strip and heavier coils are built to order. The decoiler mandrel is hand-expanded as standard, with hydraulic expansion as an option; we suggest hydraulic above about 2 t per side. Voltage is matched to your site. Feed accuracy is the feeder’s own accuracy; part accuracy also depends on the die and its pilots.

How fast does the coil side need to run?

Average strip speed in m/min = feed pitch in mm × strokes per minute ÷ 1,000. This is what the decoiler and straightener have to supply.

Average strip speed at 300 strokes per minuteAt 300 SPM, a 60 mm pitch needs 18 m/min, 100 mm needs 30, 150 mm needs 45 and 200 mm needs 60 m/min. The standard powered decoiler runs 20 m/min; laser tracking lines have been delivered at 35, 45 and 60 m/min.60 mm18 m/min100 mm30 m/min150 mm45 m/min200 mm60 m/min20 standard354560laser trackingPitch at 300 SPM
Average strip speed = pitch × SPM ÷ 1,000. Grey: standard powered decoiler (photoelectric). Orange: laser loop tracking speeds we have delivered. A non-powered decoiler can also run when the line pulls the strip steadily.

12Press and die

Stator and Rotor Stamping Machine: Press, Die and Coil Line

Buyers often ask for a stator stamping machine, rotor stamping machine, lamination stamping machine or lamination punching machine. In practice that means three things working together: a high-speed press, a progressive die and the coil line around them. Together they make an electric motor lamination press line.

Who supplies the press, the die and the coil lineThe coil line before and after the press is built by HENLI; the press comes through partner press maker GOANWIN; the progressive die comes from your die maker.Coil line in: HENLIPress: partner GOANWINDieCoil line out: HENLI
The die comes from your die maker. For a turnkey line we build the coil line and coordinate the press with GOANWIN.
Part Who supplies it What to confirm
Coil line: uncoiler, straightener, feeder, pull feeder, scrap chopper HENLI, built in its own factory Strip, pitch, speed, line direction
Stamping press for lamination (high-speed lamination press) Our partner press maker GOANWIN; we can recommend a suitable one Tonnage, bed size, shut height, stroke, SPM
Progressive die Your die maker Strip layout, pilots, release timing, stacking method

Already have a high-speed motor lamination press and die? We can build the coil line to match them. Send the press model, bed size, SPM and pass line height.

13Problems and limits

Strip Problems and Where the Line Solves Them

Most stamping trouble on a lamination line starts before the die. This table shows which station handles which problem, and which ones belong to the die and press.

Problem Usual cause Where it is handled
Coil set, crossbow, center buckle, edge wave Incoming coil Straightener improves it; it cannot remove every defect
Loop shakes, piles up or pulls tight Payoff not following the line Loop control and powered decoiler
Strip slips or buckles at speed Feeder route, release timing, loop Feeder route; pull feeder after the die
Outlet strip disturbs the die rhythm Skeleton after the die Pull feeder
Long, sharp skeleton that is hard to collect Continuous scrap Scrap chopper
Burr, slot shape, stack height Die and press Not the coil line

Limits to know before you order

1

The line starts from slit coil, so coil width should already suit the die.

2

Stamped laminations leave through the die and press outlet; tell us how you collect them.

3

A gear feeder is for fixed pitch. If the pitch changes often, use a servo route.

4

A double head decoiler shortens a coil change but does not guarantee zero downtime on its own; HENLI can engineer zero-downtime setups.

5

Published speeds are machine limits. Line speed depends on pitch, material, die and press.

6

For prototypes and very small batches, laser cutting usually makes more sense than a progressive die.

14Quote data

Quotation Data Needed

Send this data so Henli can recommend the production line instead of guessing by product name.

Stamped Product

Stator, rotor, EI/UI lamination, transformer sheet, reactor sheet or micro motor lamination. Include drawings or sample photos.

Material

Material grade, thickness, width, surface requirement, hardness or strength if available.

Coil Data

Coil ID, OD, weight, coil change frequency and whether optional head/tail joining is required.

Press and Die

Press model, tonnage, bed width, stroke, target SPM, die layout, feed pitch and release timing.

Output Side

Skeleton scrap shape, die outlet height, pulling requirement and scrap collection method.

Factory Layout

Line direction, floor space, voltage, air supply, maintenance access and whether active loop control is needed.

15FAQ

FAQ

What is a high speed motor lamination stamping line?

It is a coil-to-press production line for stamping silicon steel or electrical steel into stator, rotor, EI/UI and electromagnetic core laminations. A typical line includes coil payoff, loop tracking or brake control, S-type or U-type leveling, selected press feeding, high-speed stamping, optional pulling and scrap handling.

Can a passive decoiler line still be used for motor laminations?

Yes. A passive or unpowered decoiler with a leveler and gear feeder or high-speed single-servo feeder can work when the downstream equipment can pull the strip steadily, the coil tension is manageable and the material will not be scratched, stretched or made unstable by rear-side pulling.

Is head/tail cutting and welding required in every line?

No. Head/tail shearing and welding is an advanced coil-change option. It can reduce downtime and material loss in long-run continuous production, but many lines use passive payoff, powered payoff or loop tracking without automatic welding.

What does laser tracking do in the line?

Laser tracking reads the strip loop height continuously and changes the powered decoiler speed steplessly, so the decoiler follows the line without stop-start cycles. It is an option: a standard powered double head decoiler uses a photoelectric sensor and works start-stop at 20 m/min.

How do I choose between an S-type and a U-type leveler?

Compare them by material, feeding cycle and floor space. The U-type has more rollers and is usually chosen for EI/UI laminations, reactor sheets and other flatness-sensitive parts. The S-type is usually used on stator and rotor lines with a longer pitch.

How do I choose between GCH, GCD, gear feeder and gripper feeder?

Choose GCH for thin or wide silicon steel, longer pitch and one-feed-one-pull control. Choose GCD single servo for flexible high-speed feeding and mixed programs. Choose gear feeder for fixed short-pitch mechanical synchronization. Choose gripper feeder for narrow, thin, short-pitch and surface-sensitive strip.

When should a gripper feeder line be considered?

Use a gripper feeder route when the strip is narrow, thin, short-pitch and surface-sensitive, especially when roller feeding may slip, scratch the material or leave pressure marks. It is a specialized route for certain small motor, narrow BLDC and precision electromagnetic stamping lines.

What equipment does a lamination stamping line need?

A double head decoiler, loop control, a high-speed straightener, a feeder matched to the pitch, a high-speed press with a progressive die, and often a pull feeder and a scrap chopper after the press. HENLI builds the coil line and can recommend a partner press maker.

Do you supply the press and the die?

We build the coil line in our own factory. For the press, we work with partner press maker GOANWIN and can introduce you. The die comes from your die maker.

How thin can the line feed silicon steel?

It depends on the route. S-type and U-type straighteners and GCF gear feeders are listed from 0.1 mm, and GCH double servo feeders from 0.2 mm. HG gripper feeders are listed from 0.04 mm for precision strip in general. Tell us the grade, coating and width, and we will confirm the route.

Can the same feeder types be used for filter, chain plate, razor blade, battery or terminal stamping lines?

Some feeder types overlap, especially gear and gripper feeders for short-pitch work, but those applications require their own material, die and output-handling review. This production line is focused on motor laminations, electromagnetic cores, silicon steel and electrical steel lamination stamping.

Request a Motor Lamination Stamping Line Proposal

Send your material, coil, press, die, feed pitch and scrap discharge data. Henli can match passive or powered decoiling, laser tracking, optional coil joining, S-type or U-type leveling, feeder route, pulling control and scrap chopping according to the real production line.